RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya XB Mazda RX-7. ITEM: # 57763 TT-01
RCScrapyard Radio Controlled Models
Flags

Tamiya XB Mazda RX-7 - # 57763 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car - TT-01 Chassis:

  Released by Tamiya on March 17, 2007, the 4WD XB Mazda RX-7 (#57763) is No.63 in the RTR Pre-Assembled Expert Built Series, based on the TT-01 chassis. The Tamiya Mazda RX-7 kit (#58382) was introduced in February 2007. The model is of the Mazda RX-7 sports car that has a Wankel Rotary engine.

  A pre-painted lexan bodyshell, a 540 motor and radio system are included, but may require a battery, charger and speed controller to complete (specifications differ from country to country).

Tamiya XB Mazda RX-7 - TT-01 # 57763
▼ Scroll Down for More Images ▼


  The TT-01 is shaft driven, on a molded plastic chassis, with gear type differentials, coil spring over friction dampers, dogbone drive-shafts and bushings.

  Like the majority of Tamiya models, this model comes with plastic bush type bearings, that after a short while, when dust and grit get into them, actually wear into the metal drive shafts - our recommendation is that these should be replaced by steel shielded ball bearings ASAP.

  To get the best from the Tamiya TT-01 Chassis, it needs to be fine tuned, for smooth acceleration under control and handle corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our simple to understand, step by step procedure, will guide you to the best Set-up for your driving style.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags


Tamiya XB Mazda RX-7 - TT-01 Chassis
Tamiya TT-01 Chassis

Tamiya XB Mazda RX-7 - TT-01 Chassis
Tamiya TT-01 Chassis

Tamiya XB Mazda RX-7 - TT-01 Chassis
Tamiya TT-01 Chassis

Tamiya XB Mazda RX-7 - TT-01 Chassis
Tamiya TT-01 Chassis


Buying a Used Tamiya Mazda RX-7
Touring Car (and What to look for)


   Buying a used Tamiya Mazda RX-7 Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Mazda RX-7 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Mazda RX-7 model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Mazda RX-7 Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Mazda RX-7 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Mazda RX-7 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Mazda RX-7 model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Gearing to Win

   Just because you have the latest model, the best available batteries, the most powerful electric motor or nitro engine, doesn't mean you will go out and win everything in sight. The fastest car on the track is rarely the one that wins, it's the one that can accelerate out of corners under control and remains consistent and efficient from the start to the end of a race.

   In days gone bye, all you had to consider was the number of mili amp hours (Mah) in your battery and the current draw of your high powered motor. Gearing for a five minute race was a balancing act. But with the development of the new high capacity batteries, brushless motors and smart ESC, all that changed. Now, gearing is more of a matter of what suits your driving style and how quick your reflexes are on the sticks, the trigger and steer wheel of your transmitter. So, where do you start?

   At your local club track, you quickly find the right combination and set-up for your car by talking to the more experienced members. After a while, as your knowledge grows, tweaking a few things here and there can give you that small edge to keep you competitive. So, it follows that on tracks you don't know, you should talk to the locals there, who may be racing a similar model to your own and adjust your set-up to suit.

   Gearing correctly for any given track is absolutely crucial if your car is to be competitive.

   Too high a gearing may get you in front at the start of a race, but as your motor begins to overheat and lose efficiency, that initial advantage will soon be lost.

   Too low a gearing and although it may get you past your opposition accelerating out of the corners, you will loose that place again on the fast straights. Gearing low will always get you to the end of the race, but it will hardly ever get you on the winner's rostrum.

   Having said that, on tracks you don't know, initially it's always best to err on the side of low gearing. For your first practice laps on a new track, choose a motor that has a reasonable current draw and with a fully charged battery, try a race length run, learn the corners Ö what line to enter and exit, where you can accelerate to overtake and how fast you need to be on the straights to keep up (not overtake) the opposition. After your practice race, check the remaining capacity in your batteries and the temperature of your motor, (keep records of each motor and discover at what temperature a specific motor loses efficiency Ö all this helps when selecting the right gearing.)

   Armed with this knowledge you can then consider how to alter your gearing.

   If the motor is cool (in comparison) and your battery has ample remaining charge, try a larger pinion Ö perhaps one or two teeth more. Don't overdo it.

   An overly hot motor and low remaining capacity battery speaks for itself. The race timed practice run should have given you an insight to this problem. Obviously, in this instance you must use a smaller, less teeth pinion, or start again with a milder, less powerful motor.

   If the motor is hot, but not too hot, the battery has ample remaining charge and you did not notice any drop in efficiency towards the end of your practice run, then you are close to the optimum set up for that particular motor.

   Depending on how competitive that set-up is, you can stick with it, maybe tweak a tooth up or down, or repeat the process with a different motor to get you where you want to be.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Radio Frequencies

   After buying your first car, it won't be long before you need more than simply bashing around the back yard, or out on the street. So you will be looking around to find a club that is not too far away where you can do some serious racing.

   Before you can start racing, you will need at least three different sets of crystal frequencies. The race organisers will note down all your available frequencies when you register at the track and allocate one of those frequencies to you for your heat. To avoid change over problems from one heat to the next, they generally try to give you a frequency that no one in the heat before or after is using, but always check to make sure before you put your car down on the track and switch on.

   There is nothing more annoying than to be in the middle of your best qualifying race and some idiot switching on their transmitter in the pits, on your frequency. Not only could it spoil your race, but it could cost you a lot of money if at the time you are travelling at top speed along the straight, loose control and crash head on into the wall. Just imagine how you would feel.

   Now, imagine this scenario. You are at your RC meeting and you need to run your car to check out some changes you have made, either after a crash repair, to adjust the steering servo, or just fine tune your car before the next race. What do you do?

   Before you switch on anything, the first thing to do is check with race control, to make sure that none of the racers presently on the track or in the next heat are on the same frequency you want to use. The people in charge are always willing to help in these situations and if none of your three available frequencies are safe for you to use, they will often lend you some crystals, sometimes for a small fee.

   Some of the bigger meetings use a board displaying all the possible frequencies, indicating which of those frequencies are in use at that time and which are available for others to use. To claim a particular frequency you simply take a peg or marker off the board so that others wanting to check their car out can not use the same frequency as you. Before the next heat, this board is updated and any missing pegs must be accounted for. So obviously the best time to claim your frequency, is at the start of a heat and you must return it before the start of the next heat.

   So, be cautious, use the protocols at your track as they should be used and you won't make any enemies Ö you know it makes sense.

For More Setup Information check out my Hints and Tips page.








^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: