RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Enzo Ferrari Complete Kit. ITEM: # 57033 TT-01
RCScrapyard Radio Controlled Models
Flags

Tamiya Enzo Ferrari Complete Kit - # 57033 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car - TT-01 Chassis:

  Released by Tamiya circa 2003, the 4WD Enzo Ferrari Complete Kit (#57033) is the Enzo Ferrari (#58302) with a 540 motor, speed controller, battery, charger and radio system included. The model is of the 350kph, 650 horsepower, Enzo Ferrari launched at the 2002 Paris Auto Show that features superior down force aerodynamics and a retractable rear-wing. This model was later introduced as model number # 57049, with different included equipment.

Tamiya Enzo Ferrari Complete Kit - TT-01 # 57033
▼ Scroll Down for More Images ▼


  The TT-01 is shaft driven, on a molded plastic chassis, with gear type differentials, coil spring over friction dampers, dogbone drive-shafts and bushings.

  The kit comes with plastic bush type bearings, that after a short while, when dust and grit get into them, actually wear into the metal drive shafts - our recommendation is that these should be replaced by steel shielded ball bearings ASAP.

  To get the best from the Tamiya TT-01 Chassis, it needs to be fine tuned, for smooth acceleration under control and handle corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our simple to understand, step by step procedure, will guide you to the best Set-up for your driving style.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags


Tamiya Enzo Ferrari Complete Kit - TT-01 Chassis
Tamiya Enzo Ferrari Complete Kit Chassis

Tamiya Enzo Ferrari Complete Kit - TT-01 Chassis
Tamiya Enzo Ferrari Complete Kit Chassis


Buying a Used Tamiya Enzo Ferrari
Touring Car (and What to look for)


   Buying a used Tamiya Enzo Ferrari Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Enzo Ferrari is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Enzo Ferrari model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Enzo Ferrari Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Enzo Ferrari steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Enzo Ferrari is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Enzo Ferrari model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Battery Connectors

   Over the years I have been racing radio controlled model cars of all descriptions, I have tried a number of different connectors for my batteries.

   My first car was a Tamiya Boomerang and of course the batteries I used all had the standard Tamiya connectors, which were fine with the kit supplied 27T silver can electric motor, but I soon discovered their problem when I installed my first Modified motor. The high current demands of the motor created so much heat, the plastic surround of the connectors melted and fused together. No matter how I tried they could not be disconnected. My only option was to cut the wires.

   From there I moved over to Corally connectors, commonly referred to by many now as Bullet connectors. Comprising of a short length of 4mm gold plated tube at one end and what looks like what we used to call a Chinese lantern fitting that slotted inside the tube, also gold plated. Although they were highly efficient and reasonably easy to install and use, I never really took to this type of connector, I think it was the fact that there was always the possibility of the positive and negative being connected wrongly in poor light and also that if positioned side by side, each connector could work loose and become exposed, leaving the possibility of a short circuit.

   Then I remember buying some second hand batteries at an area meeting one day, they had these little red block connectors I soon learned were "Deans" rated at around 40 Amps. They looked like just what I was looking for so I gave them a try. They worked fine, although I didn't like the shortness of the part to be soldered. However, for about two years they were my connector of choice, until I stumbled across an advert in the "Radio Race Car International" magazine.

   The latest development in connectors at that time were named "Power Pole", made by a company called Anderson and were rated at 45 Amps. The design uses a small tube, plated with silver, with a short extending lip, that slots over the exposed wire and can either be crimped onto the wire or soldered. For safety and efficiency, I prefer the latter. To complete the connector, a colour coded plastic cover fits neatly over it.

   It was way back in 1995 I first used Power-Pole and to this day they are still the most efficient I have come across and never overheat.

   So, if you are looking for a connector to change over to, that has a high current rating and won't cause you any overheating problems "Anderson Power Pole" is the one I recommend.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Driving On Road

   The basic driving style most commonly used for all forms of on road, tarmac and carpet racing, involves using the full width of the road available and cutting each apex as tight as possible, whilst keeping complete control of the car on the track. The style, often referred to as "Rounding" looks quite simple to those watching, but to get it right needs good hand eye coordination and lots of practice.

   Consider a 180 degree turn. As you enter the corner, start with the car positioned close to the outside of the track, then as you approach the corner brake hard, but not too hard, just enough to slow the car so you maintain control and smoothly guide the car across the point of the apex, gently sweeping round until you are approximately 75% around the corner. At this point, gradually increase the throttle out of the corner, under full control and guiding the car to the opposite outside line. By the time the car is pointing straight on the track, you should be at almost full throttle, before you brake hard again for the next corner.

   Developing this driving style comes in stages. Don't try to run before you can walk, install a low powered motor and practice, practice, practice Ö until it becomes second nature. Then, as your skills improve, try something with a little more power.

   Initially set your transmitter to aggressive breaking and gradually reduce this as you get the feel of the car around the corner. Remember, the faster you enter a corner, the faster you exit it.

   When you first try out this style in a race, be patient, keep the car smooth and controlled. Remember the story about the hare and the tortoise? Well, believe me, when you first start in RC, it works.

   To make this driving style work, the car needs to have the right tires, inserts and a low centre of gravity. Adjust the suspension to provide only a small amount of body-roll and set-up guide linked below to help you set your car to suit your driving style.

   Avoid over-steer, always aim for a little under-steer. Grip is the keyword for the rounding style of driving, but not too much grip. Slicks for outdoor racing and a worn set of Hawgs I found to be best for carpet racing. If your car rolls sideways off the track as you enter the corner, try a harder tire compound, or change the damper springs or oil weights as suggested in our set-up guide. Good luck and good racing.

   If the style you are looking for is to drift slide your car around the corners, I would recommend you perfect the rounding style first, then check out my other hints and tips to learn how.

For More Setup Information check out my Hints and Tips page.








^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: