RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Stadium Raider. ITEM: #58246 TL01
RCScrapyard Radio Controlled Models
Flags

Tamiya Stadium Raider - #58246 (Radio Controlled Model Review)

1/10 Scale Electric Truck - TL-01 Chassis:

  Released by Tamiya on October 27, 1999, the Stadium Raider was nothing more than a cost cutting exercise, being essentially the TL-01 touring car chassis with buggy wheels and the Wild Dagger body shell.

Tamiya Stadium Raider - #58246 TL01
▼ Scroll Down for More Images ▼


  The TL-01 monocoque frame chassis is shaft driven four wheel drive, with orbital gear differentials front and rear. The suspension is four wheel independent double wishbone with coil spring over friction shock absorbers.

  The stick battery is positioned in the middle across the width of the chassis. Steering is via two plastic track rods of fixed length. These can be replaced with appropriate length turnbuckles if desired to allow some toe-in adjustment for improved cornering.

  The kit comes with nylon/plastic and sintered brass bush type bearings that after a short while, when dust and grit get into them, will abrade the metal drive shafts that spin in them - if you are building this kit to race seriously these should be replaced by steel, rubber shielded ball bearings.

  To drive, the high centre of gravity of the TL-01 Chassis and the friction shocks did not work well off road. Oil Filled shocks did improve the handling a little, but the chassis was never meant for gravel track racing.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:













Flags

Tamiya Stadium Raider #58246 TL-01 - Chassis
Tamiya Stadium Raider #58246 TL-01 Chassis
Tamiya Stadium Raider #58246 TL-01
Tamiya Stadium Raider #58246 TL-01 Body Shell

Buying a Used Tamiya Stadium Raider
Truck (and What to look for)


   Buying a used Tamiya Stadium Raider Electric Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Stadium Raider is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Stadium Raider model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Stadium Raider Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Truck racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Stadium Raider steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Stadium Raider is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Stadium Raider model and good racing.




▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks













Tamiya Stadium Raider


Hints and Tips

Dampers

   Dampers, Shock Absorbers, Shocks call them what you will, they are one of the least understood, but most important tools you have for adjusting the handling characteristics of your RC model.

   In this article, I will endeavour to explain just what you can achieve by making simple tweaks to your shocks and how these tweaks can keep you ahead of your opposition on the track.

   In dictionary terms "Damper" is described as "A mechanical device to absorb the energy of sudden impulses." In plain language, they stop your car from bouncing all over the track.


So how do Dampers work?

   Basically what you have is a small amount of silicone oil contained in a sealed cylinder. Through the centre of that cylinder is a metal rod and on the end of that rod, a piston with a number of small holes in it. Pulling, or pushing the rod in and out of the cylinder, your will notice a certain amount of resistance as the oil is forced through the holes in the piston. To manipulate that resistance you have two options. You could use thicker or thinner oil, or change the size of the holes in the piston. So if you have thicker oil, or smaller holes, you have more resistance. Less viscous oil or larger holes, less resistance. This simple physical relationship, coupled with a good set of tuning springs, is all you need to set-up your car to beat the rest.

   Out on the race track, the main thing you want to avoid is your car bouncing around all over the place, sliding, or even rolling over when you negotiate a tight corner. To prevent this you need to make changes, but before you make those changes you need to consider what your problem is for that particular track. How your model reacts when cornering does it Under-steer? (Slide towards the outside of the corner) or Over-steer (Turns towards the inside of the corner). Does it react differently when you exit the corner to how it did when you entered it?

   Once you have decided what your problem is, go to our "Set-Up" page linked below and follow the step by step instructions. But remember to only make ONE change at a time. If the first suggestion isn't enough to cure the problem, add the second and so on, until you find that perfect setting. Good luck and good racing.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Soldering

   In the sport of Radio Controlled racing, there are a number of things you have to learn to get you up there with the best. One of the most difficult, for those with little practical skill, is the art of Soldering.

   For their 540 silver can motors, Tamiya provide two wires, typically green and yellow, soldered to the endbell, with two bullet connectors to plug into the speed controller. While this is fine for bashing around the back yard, if you were to advance to a higher level you will soon find just how inefficient this method is.

   Motor wires are best soldered directly to the ESC. That way no energy is lost through high current draw. Some of the top drivers at one time even used to solder their batteries directly to the ESC, but these days with connectors such as "Deans" and "Power Pole" this isn't necessary but I still wouldn't use any kind of connector for the motor.

   There are basically two kinds of solder. Plumbers solder which is made up of 60% Lead and 40% Tin, where as electrical solder is the opposite 40% Lead with 60% Tin. NEVER use plumbers solder for your battery, ESC or motor joints. Lead melts at 327 degrees C, where as tin melts at 232 degrees C. The higher Lead content of plumbers means it melts at a higher temperature, which is not good for your battery cells. Also, Tin has almost half the electrical resistance of lead, so with the higher Tin content of electrical solder, electricity flows much easier to your motor.

   More recently, due to the European regulations for lead use, lead free solders are becoming more widely used well, in Europe anyway. The problem with lead free is the melting temperature it is much higher, making it difficult to produce reliable joints.

   Lead, as we know, is a poison to the body if ingested or inhaled in certain quantities. so when using lead based solder, try not to inhale any of the fumes and always wash your hands after completing your work. One of my friends also wears cotton gloves, but I find these cumbersome.

   For me lead / tin solder is far easier to use and if used with care, has less potential to damage your batteries having a much lower melting temperature.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: