RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Ford Focus WRC. ITEM #58241 TL-01.
RCScrapyard Radio Controlled Models
Flags

Tamiya Ford Focus WRC - #58241 (Radio Controlled Model)

1/10 Scale Electric Rally Car - TL-01 Chassis:

  Released by Tamiya on July 15, 1999, this TL-01 Chassis based, self assembly electric RC model, is of the Factory Team Ford Focus driven by Colin McRae in the 1999 World Rally Cross series.

  The lightweight Lexan polycarbonate body shell in this kit is an accurate copy of the cars classic lines. Decals of the Ford/Valvoline livery are included in the kit.

Tamiya Ford Focus WRC - #58241 TL-01

  The TL-01 monocoque frame chassis is shaft driven four wheel drive, with orbital gear differentials front and rear. The suspension is four wheel independent double wishbone with coil spring over friction shock absorbers.

  The stick battery is positioned in the middle across the width of the chassis. Steering is via two plastic track rods of fixed length. These can be replaced with appropriate length turnbuckles if desired to allow some toe-in adjustment for improved cornering.

  The kit comes with nylon/plastic and sintered brass bush type bearings that after a short while, when dust and grit get into them, will abrade the metal cup drive shafts that spin in them - if you are building this kit to race seriously these should be replaced by steel, rubber shielded ball bearings.

  To drive, with the standard silver can motor and smooth operating ESC, the TL01 is the ideal car for the beginner. Steering is precise and handling is predictable.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:













Flags

Tamiya Ford Focus WRC #58241 TL-01 - Chassis
Tamiya Ford Focus WRC #58241 TL-01 Chassis
Tamiya Ford Focus WRC #58241 TL-01
Tamiya Ford Focus WRC #58241 TL-01 Body Shell

Buying a Used Tamiya Ford Focus WRC
Rally Car (and What to look for)


   Buying a used Tamiya Ford Focus WRC Electric Rally Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Rally Car you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Rally Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Ford Focus WRC is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Ford Focus WRC model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Ford Focus WRC Rally Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Rally Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Rally Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Rally Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Rally Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Ford Focus WRC steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Ford Focus WRC is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Rally Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Ford Focus WRC model and good racing.


For More on how to Setup your Rally Car, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Dampers

   Dampers, Shock Absorbers, Shocks call them what you will, they are one of the least understood, but most important tools you have for adjusting the handling characteristics of your RC model.

   In this article, I will endeavour to explain just what you can achieve by making simple tweaks to your shocks and how these tweaks can keep you ahead of your opposition on the track.

   In dictionary terms "Damper" is described as "A mechanical device to absorb the energy of sudden impulses." In plain language, they stop your car from bouncing all over the track.


So how do Dampers work?

   Basically what you have is a small amount of silicone oil contained in a sealed cylinder. Through the centre of that cylinder is a metal rod and on the end of that rod, a piston with a number of small holes in it. Pulling, or pushing the rod in and out of the cylinder, your will notice a certain amount of resistance as the oil is forced through the holes in the piston. To manipulate that resistance you have two options. You could use thicker or thinner oil, or change the size of the holes in the piston. So if you have thicker oil, or smaller holes, you have more resistance. Less viscous oil or larger holes, less resistance. This simple physical relationship, coupled with a good set of tuning springs, is all you need to set-up your car to beat the rest.

   Out on the race track, the main thing you want to avoid is your car bouncing around all over the place, sliding, or even rolling over when you negotiate a tight corner. To prevent this you need to make changes, but before you make those changes you need to consider what your problem is for that particular track. How your model reacts when cornering does it Under-steer? (Slide towards the outside of the corner) or Over-steer (Turns towards the inside of the corner). Does it react differently when you exit the corner to how it did when you entered it?

   Once you have decided what your problem is, go to our "Set-Up" page linked below and follow the step by step instructions. But remember to only make ONE change at a time. If the first suggestion isn't enough to cure the problem, add the second and so on, until you find that perfect setting. Good luck and good racing.

For More Setup Information check out my Hints and Tips page.



Gear Differentials


   The Gear Differentials, commonly used in Tamiya Buggys, Trucks, Touring Cars, Monster Trucks and some of the early Tamiya Formula One and Le-Mans cars, are by design more robust than the high maintenance Ball Differentials.

   The configuration uses a main drive gear, fixed on each side of the drive axles and either three or four small metal orbital bevel gears, in a plastic gear housing, providing the drive to each side of the car when cornering, to allow the inside wheel to rotate slower than the outside wheel.

   Maintaining your Gear differentials is crucial if your car is to be competitive. Regular greasing is required, preferably molybdenum grease with graphite flakes, smeared over the gear teeth. If neglected, the gear teeth grind and wear at a rapid rate and will quickly fail, leaving you with a potentially expensive rebuild.

   For slower moving models such as Monster Trucks, Rock Crawlers and budget end Off road Buggys, Trucks and On Road Drift and Touring Cars, where low friction differential action is not essential, Gear Differentials are ideal, providing drive to each wheel as required. However, for top level competitive racing ,On and Off Road, Ball Differentials are preferable. Admittedly, they require a little more maintenance, but the benefits on the track far outweigh the negatives of the old Gear diffs.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: