RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Pennzoil Nismo GT-R. ITEM #58223 TL01.
RCScrapyard Radio Controlled Models
Flags

Tamiya Pennzoil Nismo GT-R - #58223 (Radio Controlled Model)

1/10 Scale Electric Touring Car - TL-01 Chassis:

  Released by Tamiya on September 10, 1998, this TL-01 Chassis based model, is of the Nissan Skyline Pennzoil Nismo GT-R, winner of the All-Japan Grand Touring Car Championship (JGTC) in 1998.

  The lightweight Lexan polycarbonate body shell in this kit is an accurate copy of the cars pleasing lines. Decals of the Pennzoil livery are included in the kit.

Tamiya Pennzoil Nismo GT-R - #58223 TL01

  The TL-01 monocoque frame chassis is shaft driven four wheel drive, with orbital gear differentials front and rear. The suspension is four wheel independent double wishbone with coil spring over friction shock absorbers.

  The stick battery is positioned in the middle across the width of the chassis. Steering is via two plastic track rods of fixed length. These can be replaced with appropriate length turnbuckles if desired to allow some toe-in adjustment for improved cornering.

  The kit comes with nylon/plastic and sintered brass bush type bearings that after a short while, when dust and grit get into them, will abrade the metal cup drive shafts that spin in them - if you are building this kit to race seriously these should be replaced by steel, rubber shielded ball bearings.

  To drive, with the standard silver can motor and smooth operating ESC, the TL01 is the ideal car for the beginner. Steering is precise and handling is predictable.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:













Flags

Tamiya Pennzoil Nismo GT-R #58223 TL01 - Chassis
Tamiya Pennzoil Nismo GT-R #58223 TL01 Chassis
Tamiya Pennzoil Nismo GT-R #58223 TL01
Tamiya Pennzoil Nismo GT-R #58223 TL01 Body Shell

Buying a Used Tamiya Pennzoil Nismo GT-R
Touring Car (and What to look for)


   Buying a used Tamiya Pennzoil Nismo GT-R Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Pennzoil Nismo GT-R is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Pennzoil Nismo GT-R model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Pennzoil Nismo GT-R Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Pennzoil Nismo GT-R steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Pennzoil Nismo GT-R is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Pennzoil Nismo GT-R model and good racing.


For More on how to Setup your Touring Car, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Servo Information

   Servos are found on all kinds of Radio Controlled Models. RC Touring Cars, Buggys, Trucks, Truggys, Monster Trucks, Rock Crawlers, Airplanes, Helicopters, Boats and Ships for Steering, Throttle Control, Rudder Operation and Wing Flaps.

   For complete RC beginners, choosing the right servo can be confusing, so here are a few tips to point you in the right direction.

   The standard, plastic bushed (bearings) type servos are fine to start with but come with plastic/nylon gears that can break easily in collisions. So, to protect your servo gears to some degree, make sure you have a good "servo saver".

   Servo Savers come in a number of forms and are often included as standard on some RC Models. The best ones, in my opinion, are those that use a small spring to absorb the shock of the crash and are simply fitted in place of the servo horn.

   For lightweight, small scale models, plastic geared servos are fine. But for medium to large scale RC models, I would recommend metal or titanium gear servos. These servos are by nature heavier and more costly than the plastic geared ones but are well worth the extra expense, for obvious reasons.

   Digitally controlled Servos use a microprocessor based controller board. They are generally faster, provide better torque and centralise more accurately than the older Analogue types, but again at a higher cost.

   As you advance in experience and skill, you might feel the need for something to match your lightning reflexes. Mos-FET, or simply FET Servos use Ball bearings and will provide the high speed response you crave, but at a price. However, if your budget will stretch to the higher cost, the improvement in performance can make a big difference.

For More Setup Information check out my Hints and Tips page.

Hints and Tips


Bearings

   If you are serious about your racing, looking after your bearings is essential if you are to remain competitive.
   My own experience is in both Off and On Road, National and International Car racing, but most of these tips could be useful to all forms of RC.

   Shields: The main problem with Ball Bearing Shields is they create friction and obviously the more you can reduce friction, the more efficient your bearings will be, so here's a tip that does just that.
   Wheel Bearings always come in pairs, positioned side by side. If you think about it, the two inside shields on each bearing are not required, so ... you can remove them using a small jewelers screwdriver ... simple. And in one fell swoop you have halved your wheel bearing friction.

   Cleaning: All Bearings need to be cleaned from time to time. Depending on how focused and competitive you are, this can be as often as after each race meeting, or just once or twice a year ... For Club Meetings once or twice a year might be all you need if you are easily beating your competition, but for the BIG meets you need that extra 5% or 10% just to be up with the rest.
What you need is a small glass jar, a jewelers screwdriver, an old tooth brush and some Isopropanol.
Remove the shields, then drop the bearings in the jar, add some Isopropanol, pop on the lid and shake well. Empty them out, give them a good brushing and make sure they spin free then repeat the process. Clean the shields separately. Once you are satisfied, lay them on a piece of kitchen roll and allow to dry.

   Lubrication: The arguments I have had about what lubrication to use you wouldn't believe. Some of the top racers of my day swore they didn't use any at all, but cleaned out the original lubrication and ran them dry ... they also admitted to fitting a new set after each meeting ... well, they were getting them for free.
My tip is, yes even with a new set of bearings, clean out the original lubrication (as described above) and with one shield in place use the thinnest oil you can find ... I recommend ZX1 (Zed Ex One) or sewing machine oil.

For More Setup Information check out my Hints and Tips page.







^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: