RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Nissan 350Z. ITEM #58287 TL01.
RCScrapyard Radio Controlled Models
Flags

Tamiya Nissan 350Z - #58287 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car - TL-01 Chassis:

  Released by Tamiya on December 13, 2001, this TL-01 Chassis based, self assembly electric RC model, is of the Nissan 350Z that was first seen at the 2001 Tokyo Motor Show.

  The lightweight Lexan polycarbonate body shell in this kit is an accurate reproduction of the smooth, sleek Nissan 350Z sports car lines. Decals are included in the kit.

Tamiya Nissan 350Z - #58287 TL01
▼ Scroll Down for More Images ▼


  The TL-01 monocoque frame chassis is shaft driven four wheel drive, with orbital gear differentials front and rear. The suspension is four wheel independent double wishbone with coil spring over friction shock absorbers.

  The stick battery is positioned in the middle across the width of the chassis. Steering is via two plastic track rods of fixed length. These can be replaced with appropriate length turnbuckles if desired to allow some toe-in adjustment for improved cornering.

  Plastic and sintered brass bush type bearings come as standard with this model, that after a short while, when dust and grit get into them, will abrade the metal cup drive shafts that spin in them. If you are building this kit to race seriously these should be replaced by steel shielded ball bearings.

  To drive, with the standard silver can motor and smooth operating ESC, the TL01 is the ideal car for the beginner. Steering is precise and handling is predictable.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:













Flags

Tamiya Nissan 350Z #58287 TL-01 - Chassis
Tamiya Nissan 350Z #58287 TL01 Chassis
Tamiya Nissan 350Z #58287 TL-01
Tamiya Nissan 350Z #58287 TL01 Body Shell

Buying a Used Tamiya Nissan 350Z
Touring Car (and What to look for)


   Buying a used Tamiya Nissan 350Z Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Nissan 350Z is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Nissan 350Z model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Nissan 350Z Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Nissan 350Z steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Nissan 350Z is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Nissan 350Z model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks













Tamiya Nissan-350Z


Hints and Tips

Battery Connectors

   Over the years I have been racing radio controlled model cars of all descriptions, I have tried a number of different connectors for my batteries.

   My first car was a Tamiya Boomerang and of course the batteries I used all had the standard Tamiya connectors, which were fine with the kit supplied 27T silver can electric motor, but I soon discovered their problem when I installed my first Modified motor. The high current demands of the motor created so much heat, the plastic surround of the connectors melted and fused together. No matter how I tried they could not be disconnected. My only option was to cut the wires.

   From there I moved over to Corally connectors, commonly referred to by many now as Bullet connectors. Comprising of a short length of 4mm gold plated tube at one end and what looks like what we used to call a Chinese lantern fitting that slotted inside the tube, also gold plated. Although they were highly efficient and reasonably easy to install and use, I never really took to this type of connector, I think it was the fact each connector was exposed, leaving the possibility of a short circuit.

   Then I remember buying some second hand batteries at an area meeting one day, they had these little red block connectors I soon learned were "Deans" rated at around 40 Amps. The looked like just what I was looking for so I gave them a try. They worked fine, although I didn't like the shortness of the part to be soldered. However, for about two years they were my connector of choice, until I stumbled across an advert in the "Radio Race Car International" magazine.

   The latest development of connectors at that time were named "Power Pole" and rated at 45 Amps. A small tube, plated with silver, with a short extending lip, that slotted over the exposed wire. This could either be crimped onto the wire or soldered. For safety and efficiency, I preferred the latter. Then to complete the connector, a colour coded plastic cover fitted neatly over it. The connector is still the most efficient I have come across and never overheats. That was way back in 1995 and I am still using them to this day. So, if you are looking for a connector to solve your overheating problems "Power Pole" is the one I recommend.

For More Setup Information check out my Hints and Tips page.



General Information and Advice

   RC is one of those sports that can be simply bashing around the back yard, or taken to the extreme of National and International Racing: For those who would like to enter this world of miniature Models, here are a few basic Hints: Firstly, buy a Kit not an RTR. Then, if something does break on your model, the experience you gain by building the kit will give you some idea how to fix it.

   Radio Controlled Model Cars are easily broken. Wishbones, Suspension Shock Towers, Dampers etc are prone to damage, so make sure you have a good strong front bumper and never run your car without its Body Shell in place.

   The Steering Servo is also a weakness, so if your kit does not have one, get yourself a good quality Servo Saver. I would also recommend you replace the soft steel Turnbuckles, Tie Rods and pivot/steering shafts with Titanium versions and if you get serious about your racing, lightweight Titanium Drive shafts, dog bones and CVD (Constant Velocity Drives). The standard steel ones bend far too easily.

   Gears in RC model cars often cause problems. Head on collision accidents can damage gear teeth on Nylon/Plastic Spur Gears and sometimes even the Bevel Gears inside the Gearbox. Hard impacts may also slacken the nuts and self taping screws that fix the Motor in Position, making it possible for the Pinion Gear to pull out of mesh a little and damage the teeth on your Spur Gear. To try and prevent this, you should always fit locking (Nyloc) nuts and if your mount uses self tapping screws, change the plastic motor mount occasionally to ensure a tight fit.

   Plastic Ball Connectors can cause problems. For top level Radio Controlled model car racing, they need to be checked for tightness and if considered necessary changed after every race meeting. Something like a loose fitting connector popping off could easily lose you the race, so always err on the side of caution.

   Quite a number of New car kits come with Plastic and Sintered Brass Ring type bearings. These can cause problems if at some time in the future you want to fit a full set of ball bearings so I recommend you discard the brass and plastic types before installation and get yourself a Hop-up set of Shielded Steel Ball Bearings.

   Finally, try to keep the Centre of Gravity of your model as low as you can. This can vastly improve the handling of your car when cornering at high speed. For On Road Drift/Touring cars the Ride Height should be around 5mm, for Buggys, Trucks, Truggys and Monster Trucks, as low as practical for the track conditions. Body Roll can be reduced by using Stabilizers, Anti roll or Sway Bars. Tuning Springs may also help with thicker, or thicker Silicon Oil in the Shock Absorbers. Also look towards mounting the Transponder as low as you can in the Chassis.

For Car Setup Information check out our Hints and Tips page.







^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: