RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Porsche 911 GT3 Cup VIP Complete Kit. ITEM: # 57026 TL-01
RCScrapyard Radio Controlled Models
Flags

Tamiya Porsche 911 GT3 Cup VIP Complete Kit - # 57026 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car - TL-01 Chassis:

  Released by Tamiya circa 2002, the 4WD Porsche 911 GT3 Cup VIP Complete Kit (#57026) is the Porsche 911 GT3 Cup VIP (#58283) with a 540 motor, speed controller, battery, charger and radio system included. The model is of the Becker Porsche 911 GT3 that raced in Cup series of the early 2000s.

Tamiya Porsche 911 GT3 Cup VIP Complete Kit - TL-01 # 57026
▼ Scroll Down for More Images ▼


  The TL-01 monocoque frame chassis is shaft driven four wheel drive, with orbital gear type differentials front and rear. The suspension is four wheel independent double wishbone with coil spring over friction dampers.

  The kit comes with plastic bush type bearings, that after a short while, when dust and grit get into them, actually wear into the metal drive shafts - our recommendation is that these should be replaced by steel shielded ball bearings ASAP.

  To get the best from the Tamiya TL-01 Chassis, it needs to be fine tuned, for smooth acceleration under control and handle corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our simple to understand, step by step procedure, will guide you to the best Set-up for your driving style.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:













Flags


Tamiya Porsche 911 GT3 Cup VIP Complete Kit - TL-01 Chassis
Tamiya Porsche 911 GT3 Cup VIP Complete Kit Chassis

Tamiya Porsche 911 GT3 Cup VIP Complete Kit - TL-01 Chassis
Tamiya Porsche 911 GT3 Cup VIP Complete Kit Chassis


Buying a Used Tamiya Porsche 911 GT3 Cup VIP
Touring Car (and What to look for)


   Buying a used Tamiya Porsche 911 GT3 Cup VIP Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Porsche 911 GT3 Cup VIP is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Porsche 911 GT3 Cup VIP model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Porsche 911 GT3 Cup VIP Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Porsche 911 GT3 Cup VIP steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Porsche 911 GT3 Cup VIP is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Porsche 911 GT3 Cup VIP model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Getting into RC

   When I first got into racing RC, all I had was a three year old clapped out Tamiya Boomerang, a silver can stock motor, three step mechanical speed controller, two 1400Mah stick batteries and basic Acoms stick transmitter.

   I was the newbie and most of the guys I was racing against had all the latest models, modified motors, matched batteries and top spec radio equipment, but I was still beating them easily. Why? The answer is simple: Practice. I had been driving that old car around my back yard and in the local park for almost three years. The others bought their cars only a few weeks or months earlier and had pestered their parents for the latest and most expensive car, motor etc, but did not have the experience to be able to control it. While I was steadily trundling around the track, they were crashing out on every other corner, popping ball joints, breaking wishbones and generally causing havoc.

   The moral of this story is all too obvious and anyone starting up in RC who wants to race please take note. You don't need the best equipment to win races. You can start with a cheap basic kit and with a lot of practice in some wide open spaces where you will not cause any damage, learn how to control your car. Remember don't try to run before you can walk. Stick with that silver can motor for a while and upgrade to something a little faster only when you have mastered the old one. You don't even have to buy new. If you go down to your local RC Club, there are always cars for sale. They may be battered and bruised, but if you get an old brushed silver can motor, a cheap 5A ESC, a couple of Nicad, or Nimh batteries, charger and simple radio gear, that is all you need to start practising and after a while, winning races.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Camber

   Camber is described as the angle of the wheel as you look at it directly from the front or rear of your car and if set correctly will improve your cars cornering ability considerably, by providing increased traction. This simple to make adjustment is considered by many to be one of the most effective changes you can make to your car for better handling.

   Positive Camber is when the top of the wheel is angled outwards. Negative Camber has the top of the wheel angled inwards.

   First of all, get yourself a good camber gauge. All adjustments to your cars camber setting should be made with the car in race mode that means the motor, battery etc in position in the chassis.

   To check the angle of an On Road car, it must have the ride height already set to around 5mm. Place the car on a perfectly flat surface, position your camber gauge against the side of the wheel you are checking and take the camber angle, normally this is between -1 and -3 degrees negative. Next, put a small 1mm thick piece of card under that corner of the car and push the corner down until it touches the card. In this position, check the angle again. It should be between 0 and -0.5 degrees negative camber. If not, pick up the car and put it back down on the flat surface, check and make adjustments, using the turnbuckle, that you consider are needed to achieve your goal. Keep checking and adjusting and repeat for all four corners. What you are aiming for is an angle that will provide your car with the maximum amount of rubber on the track on high speed corners.

   Off Road cars can be adjusted in a similar manner to that described previously, with the ride height set at around 20mm, but in place of the card, use a small booklet or something around 5mm thick. The optimal camber setting is a little more difficult to find for off road cars and depends generally of the track surface you are racing on. Slippery tracks generally require less camber because of reduced suspension movement when cornering, whereas high grip tracks require more camber to compensate for inertial induced body-roll. Depending on the particular model, this setting can be anything between -1 and -5 degrees sometimes more. Check your model manual for details.

   Be aware that for all model types, too much negative camber can reduce straight line traction, but with a good setting for any particular track, the advantage it gives, that of vastly improved cornering stability, far outweigh any negative effects.

   For beginners, this setting is by far the easiest to experiment with. Just take the car out on the back yard and with a few simple turns of a turnbuckle you will soon learn just what difference a small change in your cars setup can do to change its handling ability. Good luck and good racing.

For More Setup Information check out my Hints and Tips page.








^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: