RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Mazda Roadster MX-5 - #58624 M05
RCScrapyard Radio Controlled Models
Flags

Tamiya Mazda Roadster MX-5 - #58624 (Radio Controlled Model Review)

1/10 Scale Electric M-Chassis Model Car - M-05 Chassis:

  Released by Tamiya on November 28, 2015 and based on the M05 Chassis, the Mazda Roadster MX-5, was known in the USA as the Miata MX-5.

Tamiya Mazda Roadster MX-5 - M05 - #58624
▼ Scroll Down for More Images ▼


  The 2WD, FWD (front wheel drive) M05 Chassis has a lower centre of gravity than previous versions and good weight distribution which coupled with four wheel independent double wishbone suspension with coil spring over friction shock absorbers, orbital bevel gear differential and a three piece steering linkage gives excellent stability and handling on high speed corners.

  The M05 Chassis has three possible wheelbase options: The basic 210mm, M05M 225mm and M05L 239mm, that are set by changing the position of the rear suspension parts.

  Like the majority of the Tamiya budget priced Radio Controlled models, the standard kit comes with plastic and sintered brass bush type bearings, that after a short while, when dust and grit get into them, actually wear into the metal drive shafts that spin in them. If you are building this kit to race seriously these should be replaced by steel shielded ball bearings.

  To drive, the M05 Chassis has much improved balance and the low centre of gravity provides excellent stability in comparison to the first FWD short wheelbase Tamiya models, the M01 and M03. However, it still needs some skill to keep it on its wheels and just like its predecessors, provides lots of fun.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:












Flags

Tamiya Mazda Roadster MX-5 - #58624 - M05 Chassis
Tamiya M05 Chassis
Tamiya M05 Chassis
Tamiya M-05 Chassis

Buying a Used Tamiya Mazda Roadster MX-5
Touring Car (and What to look for)


   Buying a used Tamiya Mazda Roadster MX-5 Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Mazda Roadster MX-5 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Mazda Roadster MX-5 model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Mazda Roadster MX-5 Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Mazda Roadster MX-5 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Mazda Roadster MX-5 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Mazda Roadster MX-5 model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Your First Race Meeting

   When you finally find a racing club near to where you live, that initial experience of stepping up onto the rostrum and looking down over the track can be very daunting. But soon, as the race starts, adrenaline will kick in and away you go. For the next five minutes, your focus is on nothing but getting your car around each corner, avoiding all the other cars on the track and just getting to the end of the race.

   Maybe your batteries dumped or you crashed and the car was damaged, perhaps you didn't actually come last, whatever happened, it doesn't really matter you are well and truly hooked.

   When the race is over, don't be afraid to ask the more experienced racers questions about setup, driving tips etc. They have all been where you are now and will be more than willing to help you. Show them your car, get some tips on tires, gearing and general set-up for the club track.

   Then, when you get back home, go through all your races in your mind. Try to identify the things you did wrong and figure out how to avoid those mistakes next time. Think about what all the more experienced racers told you and change your settings as they advised.

   Put down a few buckets or cones in the back yard to practice driving round, something that if you hit it won't damage your car. Get someone to time you for say ten laps and each day after school, try to beat that time. The adage, "Practice makes perfect" holds true in many things, not least the sport of RC racing and as your confidence increases, your racing skills improve and the trophies begin to line up on your bedroom shelf, you will one day yourself be the guy all the newbie's look to for advice and you will remember that day, you nervously stepped up onto that platform for the first time, looked down across the track and how your whole life changed in that fleeting moment.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Keeping Notes

   If all you will ever do is go racing at your local track every week, then this article is not for you. However, if you ever look towards travelling around to different tracks around the country, or even the world, the value of keeping notes is all too obvious.

   Every time I raced in a regional or national competition meeting, I would make detailed notes, aided by a little local knowledge initially and later fine tuned to suit my own driving style.

   My experience now means there are few, if any outdoor tarmac tracks within a 300 mile radius I haven been to and my notes on motor, gearing, camber angles, shock settings, tire choice and what inserts work best for that particular track, amongst others, allow me to save valuable time on the finer points of car setup, that can be done in the warmth of my own home on the kitchen table days before the meeting, instead of the often crippling heat, or the arduous conditions inside a wind blown tent.

   There are lots of methods for making notes on setup. The easiest perhaps is to download the blank pages often supplied by your cars manufacturer with a line drawing of your car and spaces for you to fill in as to the setting you prefer. Great if each time you go to a particular track the conditions are always constant. Notes made on a cold windy day will be little use on a hot sunny days racing on the same track.

   Manufacturers setup pages for their top drivers can also be useful as a starting point, but you should never take that setup as being the best there could ever be.

   So, the first note you should make is of the weather conditions. The wind and its direction isn't really what I am talking about, although it can have an effect on your cars handling, it is not something you can change your setup to handle. Track temperature and humidity are the main things to note. Not the average for the day, but for each round of racing. And note what tires you used and how the car handled in each race. Detail everything that might be useful in the future, no matter how trivial.

   Note the motor used and the gearing. Check the temperature of the motor after the race, how much charge is left in the batteries. You may have won the race, but there is always room for improvement your competitors will be doing just that.

   Every bit of information you compile will be useful for the next time you visit that particular venue. Weather forecasts these days are far more accurate than they used to be, so the adage "fore warned is fore armed" fits the bill. Simply search through your notes and find a day you raced with similar conditions to those forecast and set up your car to suit. But don't stop there.

   The conditions may be the same as they were when you made your notes, but that doesn't mean you can't improve your setup. Your practice laps will soon prove if your previous setup was correct, or give you a basis for more fine tuning.

   If you want to be the best, you have to work at it. Success doesn't come easy. You can be the best driver around, but if your setup isn't perfect you will never step up onto the winners rostrum. My motto if you never try anything, you never do anything. And if you never do anything wrong, you aren't trying hard enough.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: