RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Ferrari F12 TDF #58644 TT-02 - Touring Car
RCScrapyard Radio Controlled Models
Flags

Tamiya Ferrari F12 TDF - #58644 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car - TT-02 Chassis:

  Released by Tamiya on May 27, 2017, based on the TT-02 chassis, the Ferrari F12 TDF was introduced by Ferrari in 2015 as a tribute to the "Tour de France" (the now defunct motorcar version) that was won by Ferrari no less than seven times.

Tamiya Ferrari F12 TDF - #58644 - TT-02
▼ Scroll Down for More Images ▼


  The TT-02 Chassis was produced by Tamiya as an entry level model, to replace the aging TT-01 Chassis, that has been around since 2003. The TT-02 design is capable of utilising modern day rechargeable batteries, is also durable and easy to build and maintain.

  The shaft driven Chassis configuration, employs front and rear orbital bevel gear differentials, fully independent double wishbone suspension with coil spring over friction dampers.

  A 540 brushed silver can electric motor and an Electronic Speed Controller (ESC) are included in the kit. Radio Equipment, Battery, Charger and paint for the body shell must be purchased separately.

  Like the majority of Tamiya budget kits, this one comes with Plastic and sintered brass Bush type bearings, that when dust and grit get into them, abrade the drive shafts that spin in them, making them sloppy and causing dog-bone problems. I recommend these should be replaced, by a full set of Shielded Ball Bearings, on initial assembly or as soon as possible.

  To get the best from the TT-02 Chassis, it needs to be fine tuned so it has enough grip to hug the corners at high speed, without slipping off the track and accelerate smoothly under control. Small adjustments can make a Big difference and our simple to understand, step by step procedure, will guide you to the best Set-up for your driving style.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:












Flags

Tamiya Ferrari F12 TDF #58644 - TT-02 Chassis
Tamiya TT-02 Chassis
Tamiya Ferrari F12 TDF #58644 - TT-02 Chassis
Tamiya TT-02

Buying a Used Tamiya Ferrari F12 TDF
Touring Car (and What to look for)


   Buying a used Tamiya Ferrari F12 TDF Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Ferrari F12 TDF is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Ferrari F12 TDF model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Ferrari F12 TDF Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Ferrari F12 TDF steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Ferrari F12 TDF is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Ferrari F12 TDF model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Toe Angle

   When you first build your RC model car, you will no doubt have made all the settings advised in the manufacturers' manual and will take it out on the back yard not thinking of things like camber, caster or toe-in I know I did. It's only when you get competitive that you start learning about these things and just what a big difference they can make to the handling of your car. One of the more effective of these adjustments is Toe-in.

   The term, toe-in, toe-out, or toe-angle, refers to the alignment of the front or rear wheels, when viewed from above. Front toe-angle is easily adjusted via the track rods or turnbuckles that link to the steering mechanism or directly to the steering servo horn. At the rear, some models like the Schumacher Mi1 can be adjusted by turnbuckles, but most models, on and off-road, have a set of hub carriers to provide the desired toe angle.

   Front toe-in reduces steering when entering a corner, but improves steering response on corner exit under acceleration. On the straights, toe-in will also improve the cars stability while accelerating.

   Front toe-out will improve steering on corner entry, but makes the car unstable under acceleration on the straights and on bumpy tracks. The usual recommendation is to have up to 1 degree of either toe-in or toe out.

   Rear toe-in is generally found as the standard setting on most on-road and off-road RC models.

   More rear toe-in provides the car with more power under-steer, as well as improved stability and rear end traction. This setting is recommended for low grip tracks.

   Less rear toe-in slightly reduces steering on corner entry, but improved steering under acceleration.

   To measure toe-angle, I used to use my trusty vernier callipers to measure the width at the front of the wheels and the rear of the wheels and using this information along with the diameter of the wheels simply calculate the angle. Or, you could alternatively use this data to draw a triangle on a sheet of paper and measure the angle with your trusty school protractor.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Driving On Road

   The basic driving style most commonly used for all forms of on road, tarmac and carpet racing, involves using the full width of the road available and cutting each apex as tight as possible, whilst keeping complete control of the car on the track. The style, often referred to as "Rounding" looks quite simple to those watching, but to get it right needs good hand eye coordination and lots of practice.

   Consider a 180 degree turn. As you enter the corner, start with the car positioned close to the outside of the track, then as you approach the corner brake hard, but not too hard, just enough to slow the car so you maintain control and smoothly guide the car across the point of the apex, gently sweeping round until you are approximately 75% around the corner. At this point, gradually increase the throttle out of the corner, under full control and guiding the car to the opposite outside line. By the time the car is pointing straight on the track, you should be at almost full throttle, before you brake hard again for the next corner.

   Developing this driving style comes in stages. Don't try to run before you can walk, install a low powered motor and practice, practice, practice until it becomes second nature. Then, as your skills improve, try something with a little more power.

   Initially set your transmitter to aggressive breaking and gradually reduce this as you get the feel of the car around the corner. Remember, the faster you enter a corner, the faster you exit it.

   When you first try out this style in a race, be patient, keep the car smooth and controlled. Remember the story about the hare and the tortoise? Well, believe me, when you first start in RC, it works.

   To make this driving style work, the car needs to have the right tires, inserts and a low centre of gravity. Adjust the suspension to provide only a small amount of body-roll and set-up guide linked below to help you set your car to suit your driving style.

   Avoid over-steer, always aim for a little under-steer. Grip is the keyword for the rounding style of driving, but not too much grip. Slicks for outdoor racing and a worn set of Hawgs I found to be best for carpet racing. If your car rolls sideways off the track as you enter the corner, try a harder tire compound, or change the damper springs or oil weights as suggested in our set-up guide. Good luck and good racing.

   If the style you are looking for is to drift slide your car around the corners, I would recommend you perfect the rounding style first, then check out my other hints and tips to learn how.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: