RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Calsonic GT-R # 44004 TGX Mk1.
RCScrapyard Radio Controlled Models
Flags

Tamiya Calsonic GT-R - # 44004 (Radio Controlled Model)

1/8 Scale Nitro Rally/Touring Car: TGX Mk1 Chassis

  Released by Tamiya on July 31, 1996, the 4WD Calsonic GT-R - # 44004 - is No.4 in the Glow-Engine RC Car Series and was based on the TGX Mk1 chassis with an OPS VR-15s engine.

Tamiya Calsonic GT-R - 44004 - 1:8 Nitro On Road

  The model is shaft driven, on an alloy plate chassis, with gear type differentials, coil spring over oil filled dampers, dogbone drive-shafts, bushings and some ball bearings.

  Like the majority of Tamiya RC models, this model comes with plastic and sintered brass bush type bearings, that after a short while, when dust and grit get into them, actually abrade the metal shafts that spin in them - our recommendation is that these should be replaced by steel shielded ball bearings ASAP.

  To race the Tamiya Calsonic GT-R, it requires time and patience, to tune and adjust for improvements in handling and steering ability and to get the grip you need to stay on course when manoeuvring around tight, slippery corners. A little can be a lot when it comes to changing your cars settings and our easy methodical directions will guide you to the best Set-up to help you win and keep you winning.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags


★ Tamiya 44031 TGX Mk1 Chassis ★
Tamiya TGX Mk1 Chassis

★ Tamiya TGX Mk1 Chassis ★
Tamiya TGX Mk1 Chassis

★ Tamiya TGX Mk1 Chassis ★
Tamiya TGX Mk1 Chassis


Buying a Used Tamiya TGX Mk1
Touring Car (and What to look for)


   Buying a used Tamiya TGX Mk1 Nitro Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the road.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya TGX Mk1 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your TGX Mk1 model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your TGX Mk1 Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The TGX Mk1 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya TGX Mk1 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your TGX Mk1 model and good racing.


For More on how to Setup your Touring Car, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Sway Bars

   On most forms of RC model cars, Sway Bars, also referred to as Stabilizers, Torsion Bars, or more commonly in some parts as Anti Roll Bars, are often nothing more than a short length of spring steel, clamped to the chassis or sometimes the gearbox of the car, extending out to the lower wishbones direct or connected to the wishbones using short adjustable or fixed length links and ball joints, depending on their position.

   The principal behind the Sway Bar is simple. As the car enters a corner, weight is transferred to the outside wheels, the chassis rolls due to inertia and the suspension dips and grip on the inside wheels is reduced. In an effort to counter this dipping effect and transfer some grip back to the inside wheels to improve traction as you exit the corner, the sway bars transfer the dip of the outside, to pull down the inside wishbones, improving grip on the outside wheels and improving overall stability.

   Sounds complicated I know, but for some tracks sway bars can be a useful tool when you have exhausted all other options to correct your handling problems.

   Tuning your Sway Bars is quite easy. Some manufacturers do offer colour coded tuning sets with varying thicknesses of spring steel wire, but the best way is to change the position the bar is attached to the wishbone, or on some variations you have the option of positioning the link on the Sway Bar itself. By simply moving a small collet clamped along the short length of the bar. Closer to the central pivot point reduces the leverage of the bar and effectively increasing its resistance, further away from the pivot point reducing resistance. More fine tuning can be achieved by adjusting the length of the turnbuckle link (if available) to pre load the bar.

   Personally, before I ever installed any sway bars I would always try changing damper tuning springs and oil viscosity settings, especially if the track was uneven and bumpy, in which case the effectiveness of the bars was minimal if at all.

   For those more into Drifting, Sway Bars can be an easy way to fine tune your car. A single turn on the turnbuckle links can be a way to simply increase or decrease wheel traction that minute amount you need to get the perfect balance.

   For more on how to use Sway Bars check out our Set-up tips page linked below.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Driving On Road

   The basic driving style most commonly used for all forms of on road, tarmac and carpet racing, involves using the full width of the road available and cutting each apex as tight as possible, whilst keeping complete control of the car on the track. The style, often referred to as "Rounding" looks quite simple to those watching, but to get it right needs good hand eye coordination and lots of practice.

   Consider a 180 degree turn. Start with the car positioned towards the outside of the track, then as you approach the corner brake hard and as smooth as you can, guide the car across the point of the apex, gently sweeping round until you are approximately 75% around the corner. At this point, gradually increase the throttle out of the corner, maintaining control and guiding the car to the opposite outside line. By the time the car is straight on the track, you should be at almost full throttle, before you brake hard again for the next corner.

   Developing this driving style comes in stages. Don't try to run before you can walk, install a low powered motor and practice, practice, practice until it becomes second nature. Then, as your skills improve, try something with a little more power.

   Initially set your transmitter to aggressive breaking and gradually reduce this as you get the feel of the car around the corner. Remember, the faster you enter a corner, the faster you exit it.

   When you first try out this style in a race, be patient, keep the car smooth and controlled. Remember the story about the hare and the tortoise? Well, believe me, when you first start in RC, it works.

   To make this driving style work, the car needs to have the right tires, inserts and a low centre of gravity, low body-roll set-up. Grip is the keyword in this instance, without that, your car will slide out of control and you will loose the race.

   If the style you are looking for is to drift slide your car around the corners, I would recommend you perfect the rounding style first, then check out my other hints and tips to learn how.

For More Setup Information check out my Hints and Tips page.








^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: