RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Toyota FJ Cruiser Black Special. ITEM: #58620 CC-01
RCScrapyard Radio Controlled Models
Flags

Tamiya Toyota FJ Cruiser Black Special - #58620 (Radio Controlled Model)

1/10 Scale Electric Truck - CC-01 Chassis:

  Released by Tamiya on October 17, 2015, the Toyota FJ Cruiser Black Special, is based on the well respected CC-01 Cross Country chassis.

  The kit includes a TBLE-02S ESC that can be used with brushed and brushless motors and a 540 brushed motor. Radio equipment, battery, charger and paint are required to complete.

Tamiya Toyota FJ Cruiser Black Special - CC-01 #58620

  This CC-01 chassis was first used on the Mitsubishi Pajero (#58132) in 1993 and over the years more than thirty Radio Controlled models, including this one, have been based on this tough, durable design.

  To build, the Truck was simple and straightforward. The step by step instruction and assembly manual, provided in the kit by Tamiya, sets out each stage of the trucks construction in easy to follow diagrammatic detail.

  The 4WD bathtub CC-01 chassis employs two orbital gear differentials, coil spring over oil filled shock absorbers and dog-bone drive shafts. The front and rear gearboxes are linked via a steel universal jointed prop shaft.

  Like most Tamiya models, the kit comes with plastic and sintered brass bushings (ring type bearings) that after a short while, when dust and grit is collected by the lubricating grease, will actually wear into the metal drive shafts that spin in them - if you are building this kit to race seriously these should be replaced by steel shielded ball bearings ASAP.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya Toyota FJ Cruiser Black Special #58620 CC-01 - Chassis
Tamiya CC-01 Chassis
Tamiya Toyota FJ Cruiser Black Special #58620 CC-01
Tamiya CC-01

Buying a Used Tamiya Toyota FJ Cruiser
Truck (and What to look for)


   Buying a used Tamiya Toyota FJ Cruiser Electric Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Toyota FJ Cruiser is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Toyota FJ Cruiser model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Toyota FJ Cruiser Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Truck racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Toyota FJ Cruiser steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Toyota FJ Cruiser is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Toyota FJ Cruiser model and good racing.


For More on how to Setup your Truck, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Getting into RC

   When I first got into racing RC, all I had was a three year old clapped out Tamiya Boomerang, a silver can stock motor, three step mechanical speed controller, two 1400Mah stick batteries and basic Acoms stick transmitter.

   I was the newbie and most of the guys I was racing against had all the latest models, modified motors, matched batteries and top spec radio equipment, but I was still beating them easily. Why? The answer is simple: Practice. I had been driving that old car around my back yard and in the local park for almost three years. The others bought their cars only a few weeks or months earlier and had pestered their parents for the latest and most expensive car, motor etc, but did not have the experience to be able to control it. While I was steadily trundling around the track, they were crashing out on every other corner, popping ball joints, breaking wishbones and generally causing havoc.

   The moral of this story is all too obvious and anyone starting up in RC who wants to race please take note. You don't need the best equipment to win races. You can start with a cheap basic kit and with a lot of practice in some wide open spaces where you will not cause any damage, learn how to control your car. Remember don't try to run before you can walk. Stick with that silver can motor for a while and upgrade to something a little faster only when you have mastered the old one. You don't even have to buy new. If you go down to your local RC Club, there are always cars for sale. They may be battered and bruised, but if you get an old brushed silver can motor, a cheap 5A ESC, a couple of Nicad, or Nimh batteries, charger and simple radio gear, that is all you need to start practising and after a while, winning races.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Choosing a Transmitter

   When you first started in RC, you may have purchased a package that came with the car kit, motor, battery, charger, ESC and radio system complete. The transmitter was probably just a basic steer wheel, or stick type, with nothing more than forward, reverse, left, right and simple trim settings to centralise the servo and ESC.

   After a while, as your enthusiasm grows and your experience increases, you will want to move on to a better radio system, with more setting options, but where do you begin?

   Choosing the right transmitter is a personal thing. It has to feel right, have the balance you like, not be too bulky for your hand size and have all the features you might need to set up your car to your driving style.

   Transmitters these days are highly sophisticated pieces of engineering and once you choose your transmitter you will probably stick with it for the rest of your competitive career.

   Don't just go for the one you see in a review that looks and sounds like the best thing there could ever be and comes at a bargain price. Then when it arrives through the post and you get it in your hands it just doesn't have the feel you thought it would have. Sits awkwardly in your hands and is so complicated to set up you need a university degree to understand it.

   Talk to the experienced racers at your local track, ask them their opinion, see what their transmitter is like and if they will allow you to, hold it in your hands and see how it feels. All the best buys in life are made by recommendation. Then, once you have some idea what you are looking for, look on the internet for that model to get the best price, or go to a dealer and check out the latest models.

   Frequency choice depends on where in the world you live and what form of RC you are into. Fortunately, most of the top end transmitters can change to different frequency ranges by simply fitting a different module, so if you ever move up to an international level, you don't have to buy a new transmitter, just a module and receiver.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: