RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Mitsubishi Pajero Rally. ITEM: #58602 CC-01
RCScrapyard Radio Controlled Models
Flags

Tamiya Mitsubishi Pajero Rally - #58602 (Radio Controlled Model Review)

1/10 Scale Electric Truck - CC-01 Chassis:

  Released by Tamiya on February 28, 2015, based on the Cross Country CC-01 chassis, the Tamiya Mitsubishi Pajero Rally, (also known as the Montero or Shogun) is of the Mitsubishi SUV that was raced around the world, most famously in the Dakar Rally.

  The kit includes a TBLE-02S ESC that can be used with brushed and brushless motors and a 540 brushed motor. Radio equipment, battery, charger and paint are required to complete.

Tamiya Mitsubishi Pajero Rally - CC-01 #58602
▼ Scroll Down for More Images ▼


  This CC-01 chassis was first used on the Mitsubishi Pajero (#58132) in 1993 and over the years more than thirty Radio Controlled models, including this one, have been based on this tough, durable design.

  To build, the Truck was simple and straightforward. The step by step instruction and assembly manual, provided in the kit by Tamiya, sets out each stage of the trucks construction in easy to follow diagrammatic detail.

  The 4WD bathtub CC-01 chassis employs two orbital gear differentials, coil spring over oil filled shock absorbers and dog-bone drive shafts. The front and rear gearboxes are linked via a steel universal jointed prop shaft.

  Like most Tamiya models, the kit comes with plastic and sintered brass bushings (ring type bearings) that after a short while, when dust and grit is collected by the lubricating grease, will actually wear into the metal drive shafts that spin in them. If you are building this kit to race seriously these should be replaced by steel shielded ball bearings ASAP.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya Mitsubishi Pajero Rally #58602 CC-01 - Chassis
Tamiya Mitsubishi Pajero Rally #58602 CC-01 Chassis
Tamiya Mitsubishi Pajero Rally #58602 CC-01
Tamiya Mitsubishi Pajero Rally #58602 CC-01

Buying a Used Tamiya Mitsubishi Pajero Rally
Truck (and What to look for)


   Buying a used Tamiya Mitsubishi Pajero Rally Electric Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Mitsubishi Pajero Rally is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Mitsubishi Pajero Rally model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Mitsubishi Pajero Rally Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Truck racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Mitsubishi Pajero Rally steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Mitsubishi Pajero Rally is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Mitsubishi Pajero Rally model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Ackerman

   So What is Ackerman?

   If you place your car on a table facing away from you and turn the steering to full lock to the left, you will notice the angle the left hand wheel has turned is more than that of the right hand wheel. That is the Ackerman effect.

   Moving your car to the edge of the table, with the wheels still on full lock, push it round a complete circle. What you will notice, is the diameter of the circle made by the inside wheel, is smaller than that of the outside wheel. This is a good thing.

   Consider what would happen if both wheels turned to the same angle. In this example, the inside wheel would have a tendency to drag sideways, making the car unstable and difficult to drive.

   The standard kit setting on the majority of RC Model cars, are generally pretty good for beginners, but when your experience increases, you will find out just what tuning your Ackerman can do for your driving style and why it can be helpful when setting up your car for any particular track.

   Some of the cheaper RC Models have fixed position steering links. Others have various methods to change Ackerman settings, like changing shims under the ball connector etc. These days, most modern cars allow you to adjust your Ackerman by lengthening or shortening the links by simply removing two screws and repositioning the links in relation to the front suspension arms.

   Lengthening the links, by adjusting the pivot points of the steering arms back towards the centre line of the rear axle, will give you Less Ackerman, providing you with more aggressive steering as you enter a corner. Useful on slippery tracks, to counter when the car tends to slide to the outside of the corner as you first turn into it.

   Shortening the links, by adjusting the pivot points of the steering arms more forward of the centre line of the rear axle, will give you More Ackerman, making cornering less aggressive, more predictable and improving car stability, better for high grip tracks, with smooth sweeping corners.

   How to implement these adjustments varies from model to model so you will have to refer to your manual for full instructions.

For More Setup Information check out my Hints and Tips page.



General Information and Advice

   RC is one of those sports that can be simply bashing around the back yard, or taken to the extreme of National and International Racing: For those who would like to enter this world of miniature Models, here are a few basic Hints: Firstly, buy a Kit not an RTR. Then, if something does break on your model, the experience you gain by building the kit will give you some idea how to fix it.

   Radio Controlled Model Cars are easily broken. Wishbones, Suspension Shock Towers, Dampers etc are prone to damage, so make sure you have a good strong front bumper and never run your car without its Body Shell in place.

   The Steering Servo is also a weakness, so if your kit does not have one, get yourself a good quality Servo Saver. I would also recommend you replace the soft steel Turnbuckles, Tie Rods and pivot/steering shafts with Titanium versions and if you get serious about your racing, lightweight Titanium Drive shafts, dog bones and CVD (Constant Velocity Drives). The standard steel ones bend far too easily.

   Gears in RC model cars often cause problems. Head on collision accidents can damage gear teeth on Nylon/Plastic Spur Gears and sometimes even the Bevel Gears inside the Gearbox. Hard impacts may also slacken the nuts and self taping screws that fix the Motor in Position, making it possible for the Pinion Gear to pull out of mesh a little and damage the teeth on your Spur Gear. To try and prevent this, you should always fit locking (Nyloc) nuts and if your mount uses self tapping screws, change the plastic motor mount occasionally to ensure a tight fit.

   Plastic Ball Connectors can cause problems. For top level Radio Controlled model car racing, they need to be checked for tightness and if considered necessary changed after every race meeting. Something like a loose fitting connector popping off could easily lose you the race, so always err on the side of caution.

   Quite a number of New car kits come with Plastic and Sintered Brass Ring type bearings. These can cause problems if at some time in the future you want to fit a full set of ball bearings so I recommend you discard the brass and plastic types before installation and get yourself a Hop-up set of Shielded Steel Ball Bearings.

   Finally, try to keep the Centre of Gravity of your model as low as you can. This can vastly improve the handling of your car when cornering at high speed. For On Road Drift/Touring cars the Ride Height should be around 5mm, for Buggys, Trucks, Truggys and Monster Trucks, as low as practical for the track conditions. Body Roll can be reduced by using Stabilizers, Anti roll or Sway Bars. Tuning Springs may also help with thicker, or thicker Silicon Oil in the Shock Absorbers. Also look towards mounting the Transponder as low as you can in the Chassis.

For Car Setup Information check out our Hints and Tips page.







^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: