RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Ford SVT Mustang Cobra-R. ITEM #58169 TA02.
RCScrapyard Radio Controlled Models
Flags

Tamiya Ford SVT Mustang Cobra-R - #58169 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car - TA-02 Chassis:

  Released by Tamiya on January 18, 1996, this TA-02 Chassis based, self assembly electric RC model, is of the Snipes Racing Hacker Express #00 Ford SVT Mustang Cobra-R. The lightweight Lexan polycarbonate body shell in this kit is a faithful copy the cars classic lines. Decals of the cars distinctive USA flag livery are included in the kit.

Tamiya Ford SVT Mustang Cobra R - #58169 TA02
▼ Scroll Down for More Images ▼


  The TA-02 ABS bathtub chassis is shaft driven four wheel drive, with orbital gear differential at the front and Ball differential at the rear. The suspension is four wheel independent double wishbone with plastic Coil Spring over Oil Filled shock absorbers.

  Many TA-02 owners consider the drive train to be poor and inefficient, also the ball differential often works loose, losing drive.

  The kit comes with Plastic and sintered brass bush type bearings, that after a short while, when dust and grit get into them, actually wear into the metal cup drive shafts. If you are building this kit to race seriously these should be replaced by steel shielded ball bearings.


      Rating: 3.53.5 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:















Flags

Tamiya Ford SVT Mustang Cobra-R #58169 TA02 - Chassis
Tamiya Ford SVT Mustang Cobra-R #58169 TA02 Chassis
Tamiya Ford SVT Mustang Cobra-R #58169 TA02
Tamiya Ford SVT Mustang Cobra-R #58169 TA02 Body Shell

Buying a Used Tamiya Ford SVT Mustang Cobra-R
Touring Car (and What to look for)


   Buying a used Tamiya Ford SVT Mustang Cobra-R Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Ford SVT Mustang Cobra-R is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Ford SVT Mustang Cobra-R model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Ford SVT Mustang Cobra-R Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Ford SVT Mustang Cobra-R steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Ford SVT Mustang Cobra-R is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Ford SVT Mustang Cobra-R model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks













Tamiya Ford-Mustang-Cobra-R


Hints and Tips

Radio Gear

How to avoid Interference.


1/  The first consideration when installing your Receiver into your Electrically Powered Model is to make sure it is well away from the Negative Battery terminal and the Motor. The Magnetic field can cause stuttering type interference at times of high current draw (i.e., Fast Acceleration)

2/  Make sure the Ariel tube is long enough for the Ariel wire. The tip of this wire is highly sensitive and should be as high and as far away from the Motor as possible (yup, its that magnetic field prob again)

3/  If all else fails, a simple tip that often works for all RC Model enthusiasts is to wrap the receiver in Aluminium Foil, to shield against any magnetic and external radio interference.

4/  As a last resort, to protect against servo twitch, try ferrite beads. (available at Radio Shack or Maplins) These are threaded over the red, white (or yellow) and black wires of each servo.

5/  If you are using a FET Servo, the installation of a choke (a small electrical component) in the positive feed wire will smooth out any current spikes and reduce the possibility of "servo twitch".

6/  Another thing you might try is a "glitch buster" or "stutter stopper". Basically, this is a capacitor that simply plugs into your Radio Receiver and attempts to keep a level voltage supply to the Radio system.

For More Setup Information check out my Hints and Tips page.


Information and Advice

Electronic Speed Controllers

History:

   ESC were originally developed to be used in conjunction with brushed 27T stock and modified motors in the late 1970s, early 1980s. Compared to modern day Controllers, they were Bulky and heavy, constructed using basic resistors, rheostats, capacitors and transistors, crammed together on a simple circuit board, to provide stepped but smooth acceleration when compared to the old mechanical, servo operated sweeper Speed Controllers. An Electronic Switch to change the direction of current flow was used on some of these early ESC to give reverse operation. Although they were a vast improvement on the old mechanical speedos of the time, they were expensive, jerky to control and prone to burn out if not carefully looked after.

   As new technology became available, improvements were slowly made and with the introduction of the new FET (Field Effect Transistors) and some basic mass produced silicon chips, ESC were made smaller and their reliability gradually improved.

   By the mid 1990s, "regenerative breaking" was developed. This meant that energy that would have been lost slowing down the car by effectively turning the motor into a generator, was harvested and put back into the battery. This of course was long before F1 had KERS (Kinetic Energy Recovery System) and adjustable anti lock breaking was introduced.

   Brushless Motors came to RC in the late 1990s early 2000s, which required a new breed of ESC to be developed to fully utilise the new technology. Ni-Cad Rechargeable Batteries were superseded by Ni-Mh and more recently Li-Po Batteries which provided higher Current output for the ESC to regulate. The latest ESC now use sensors to manage the motor and can be adjusted remotely to suit varying conditions.


Brushed Motor ESC.

   The "Silver Can" Stock Motors that come in a wide number of RC model kits are often accompanied by a 5 Amps to 20 Amps ESC. However, if you want to upgrade to a more powerful Modified Brushed Motor, 20 Amps may not be enough, so you will have to buy a something well over 20 Amps depending on the number of turns of your motor. As a rough guide, a 9 Single has a much higher current requirement than 20 Single.

Brushless Motor ESC.

   ESC for Brushless Motors are in no way compatible with brushed motors. The DC (Direct Current) input from the battery, on brushless ESC is transformed into three phase AC (Alternating Current). Each "phase" connecting three wires on the Brushless motor. By changing the frequency of the output wave the motor will spin faster for acceleration or slower for breaking. Reverse is simply achieved by changing over any two of the three "phases".
   At the time this article was written, Brushless ESC range from 3 Amps to around 300 Amps.
   For beginners I recommended you buy an ESC and Motor Combo, that way you can be sure the ESC Current rating is correct for the Motor.


For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: