RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Eunos Roadster. (Mazda MX-5 / MX-5 Miata) ITEM #58180 M-02M.
RCScrapyard Radio Controlled Models
Flags

Tamiya Eunos Roadster - #58180 (Radio Controlled Model)

1/10 Scale Electric M-Chassis Model Car - M-02M Chassis:

  Released by Tamiya on August 6, 1996, this self assembly Radio Controlled Model, based on the medium wheelbase version of the M02 chassis, the M02M, is of the car known in Japan as the Mazda Eunos Roadster, in Europe as the MX-5 and in North America as the MX-5 Miata.

Tamiya Eunos-Roadster or Mazda MX-5 or MX-5 Miata - #58180 M-02M

  The first M-Chassis model, designated the M01, was released in 1994, specifically for the Rover Mini Cooper (#58149) as a Front mounted motor, Front Wheel Drive model. The M02 is exactly the opposite. Rear mounted motor, Rear Wheel Drive.

  The design is not without its problems however. The curious steering set-up isn't the best and the horizontally mounted friction mono shocks are next to useless for fine tuning. Changing these for oil filled versions and softer springs, improves the cars handling considerably.

  Like the majority of the radio controlled models produced by Tamiya around 80s and 90s the car disappointingly came with the plastic/nylon and sintered brass bush type bearings. If installed, the grease on these bearings collect dust and grit that actually abrades the shafts spinning in them, so if you do fit ball bearings at a later time they are sloppy on the shafts not good To avoid this problem, a full set of steel ball bearings should be installed on first build.


      Rating: 3.53.5 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:













Flags

Tamiya Eunos Roadster #58180 M-02M - Chassis
Tamiya Eunos Roadster #58180 M-02M Chassis
Tamiya Eunos Roadster #58180 M-02M
Tamiya Eunos Roadster #58180 M-02M Body Shell

Buying a Used Tamiya Eunos Roadster
Touring Car (and What to look for)


   Buying a used Tamiya Eunos Roadster Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Eunos Roadster is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Eunos Roadster model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Eunos Roadster Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Eunos Roadster steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Eunos Roadster is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Eunos Roadster model and good racing.


For More on how to Setup your Touring Car, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks













Tamiya Eunos-Roadster M02M


Hints and Tips

Gearing to Win

   Just because you have the latest model, the best available batteries, the most powerful electric motor or nitro engine, doesn't mean you will go out and win everything in sight. The fastest car on the track is rarely the one that wins, it's the one that can accelerate out of corners under control and remains consistent and efficient from the start to the end of a race.

   In days gone bye, all you had to consider was the number of mili amp hours (Mah) in your battery and the current draw of your high powered motor. Gearing for a five minute race was a balancing act. But with the development of the new high capacity batteries, brushless motors and smart ESC, all that changed. Now, gearing is more of a matter of what suits your driving style and how quick your reflexes are on the sticks, the trigger and steer wheel of your transmitter. So, where do you start?

   At your local club track, you quickly find the right combination and set-up for your car by talking to the more experienced members. After a while, as your knowledge grows, tweaking a few things here and there can give you that small edge to keep you competitive. So, it follows that on tracks you don't know, you should talk to the locals there, who may be racing a similar model to your own and adjust your set-up to suit.

   Gearing correctly for any given track is absolutely crucial if your car is to be competitive.

   Too high a gearing may get you in front at the start of a race, but as your motor begins to overheat and lose efficiency, that initial advantage will soon be lost.

   Too low a gearing and although it may get you past your opposition accelerating out of the corners, you will loose that place again on the fast straights. Gearing low will always get you to the end of the race, but it will hardly ever get you on the winner's rostrum.

   Having said that, on tracks you don't know, initially it's always best to err on the side of low gearing. For your first practice laps on a new track, choose a motor that has a reasonable current draw and with a fully charged battery, try a race length run, learn the corners what line to enter and exit, where you can accelerate to overtake and how fast you need to be on the straights to keep up (not overtake) the opposition. After your practice race, check the remaining capacity in your batteries and the temperature of your motor, (keep records of each motor and discover at what temperature a specific motor loses efficiency all this helps when selecting the right gearing.)

   Armed with this knowledge you can then consider how to alter your gearing.

   If the motor is cool (in comparison) and your battery has ample remaining charge, try a larger pinion perhaps one or two teeth more. Don't overdo it.

   An overly hot motor and low remaining capacity battery speaks for itself. The race timed practice run should have given you an insight to this problem. Obviously, in this instance you must use a smaller, less teeth pinion, or start again with a milder, less powerful motor.

   If the motor is hot, but not too hot, the battery has ample remaining charge and you did not notice any drop in efficiency towards the end of your practice run, then you are close to the optimum set up for that particular motor.

   Depending on how competitive that set-up is, you can stick with it, maybe tweak a tooth up or down, or repeat the process with a different motor to get you where you want to be.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Painting a Lexan Body Shell.

   Most RC Model kits come with an unpainted, clear Lexan plastic Body Shell you yourself must prepare and paint. This type of Body Shell is painted on the inside and special spray or brush on Polycarbonate Paints MUST be used.

   The beauty of this is you can go wild and show off your artistic ability, or simply choose your favourite colour and add some choice decals later.

   This article is for those who have never done this kind of thing before and need some basic guidance.


   Firstly, cut off the waste from the body shell with sharp scissors. If required finish off the rounded wheel arches with smooth sandpaper wrapped around a drinks can.

   Any holes for body posts must also be drilled before painting. Place the clear body shell over the model and adjust the posts so the shell is in the desired position. Where the posts touch the shell make a small dot with a marker pen.
Next, pierce small holes in the shell where the dots are from the inside. Place the shell on an old piece of wood and drill the post holes, again, from the inside.

   The next thing to do is clean it inside and out. Any small amount of impurity such as oil or grease could impair the adhesion of the paint.
For this, fill a bowl with water and use a small amount of washing up liquid with a soft sponge. Never use a scourer. Rinse well to ensure no residue remains.

   Most Body Shells come with a set of sticky back paper masks for the windows etc that are positioned on the inside. If not supplied, you will have to either make your own, or use masking tape. Run your thumb nail around the edges of each mask to ensure contact paint can creep into any open area and easily ruin your hard work, so please be vigilant.

   Tip: To protect against paint spilling out onto the outside of the body shell, use masking tape around the outside edges and wheel arches.

   Now you are ready to begin applying your paint. Find a well ventilated area and if spraying, use a breathing mask.
Three or four sprayed, or at least two brushed layers are recommended allowing around thirty minutes between layers.

   Once the paint is fully dry, to protect the paint from scratching, spray or brush over it with one or two layers of clear plastic varnish.

   When the varnish is completely dry, carefully remove the window masks. If necessary, use a modelling knife to lift an edge to grasp between your thumb and finger DO NOT RUSH.

   Decals can now be placed on your body shell. So they adhere better I recommend any square edges are rounded. This reduced the tendency for them to peel off.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: