RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Toyota Tundra High-Lift. ITEM: #58415
RCScrapyard Radio Controlled Models
Flags

Tamiya Toyota Tundra High-Lift - #58415 (Radio Controlled Model Review)

1/10 Scale Electric Truck - HL Chassis:

  Released by Tamiya on October 28, 2008, this Tamiya Radio Controlled Truck model, is of the Toyota Tundra High-Lift.

  The chassis, first used for the Ford F350 High-Lift (#58372), features a realistic ladder frame, 3-speed transmission, shaft driven 4WD configuration with slipper clutch. Also a highly detailed injection molded body and large diameter wheels that enhance the models stylish high ground clearance look.

Tamiya Toyota Tundra High-Lift - #58415
▼ Scroll Down for More Images ▼


  The Differential features tough metal gears that can be locked to provide awesome off-road ability.

  Special features abound in this model, including: metal parts such as a ladder frame, under guard, front guard, leaf springs and aluminium, coil spring enclosed friction dampers, roll bar, road light, front grille, front/rear bumper, side-step, diff guard, (wheels and exhaust feature a metal-plated finish).

  The Toyota Tundra High-Lift drives superbly and needs little modification to be competitive. However, a certain amount of experience is required. Not a model for beginners.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya Toyota Tundra High-Lift #58415 - Chassis
Tamiya Toyota Tundra High Lift Ladder Frame Chassis - #58415
Tamiya Toyota Tundra High-Lift #58415
Tamiya Toyota Tundra High-Lift #58415 Body Shell

Buying a Used Tamiya Toyota Tundra High-Lift
Truck (and What to look for)


   Buying a used Tamiya Toyota Tundra High-Lift Electric Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Toyota Tundra High-Lift is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Toyota Tundra High-Lift model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Toyota Tundra High-Lift Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Truck racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Toyota Tundra High-Lift steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Toyota Tundra High-Lift is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Toyota Tundra High-Lift model and good racing.




▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks













Tamiya Toyota Tundra High Lift - #58415


Hints and Tips

Servo Information

   Servos are found on all kinds of Radio Controlled Models. RC Touring Cars, Buggys, Trucks, Truggys, Monster Trucks, Rock Crawlers, Airplanes, Helicopters, Boats and Ships for Steering, Throttle Control, Rudder Operation and Wing Flaps.

   For complete RC beginners, choosing the right servo can be confusing, so here are a few tips to point you in the right direction.

   The standard, plastic bushed (bearings) type servos are fine to start with but come with plastic/nylon gears that can break easily in collisions. So, to protect your servo gears to some degree, make sure you have a good "servo saver".

   Servo Savers come in a number of forms and are often included as standard on some RC Models. The best ones, in my opinion, are those that use a small spring to absorb the shock of the crash and are simply fitted in place of the servo horn.

   For lightweight, small scale models, plastic geared servos are fine. But for medium to large scale RC models, I would recommend metal or titanium gear servos. These servos are by nature heavier and more costly than the plastic geared ones but are well worth the extra expense, for obvious reasons.

   Digitally controlled Servos use a microprocessor based controller board. They are generally faster, provide better torque and centralise more accurately than the older Analogue types, but again at a higher cost.

   As you advance in experience and skill, you might feel the need for something to match your lightning reflexes. Mos-FET, or simply FET Servos use Ball bearings and will provide the high speed response you crave, but at a price. However, if your budget will stretch to the higher cost, the improvement in performance can make a big difference.

For More Setup Information check out my Hints and Tips page.

Hints and Tips

Tires for RC Models

Rubber Tires:

   Rubber Tires ALWAYS should have either soft sponge or rubber inserts. They will not function as they should without them. And if you are totally serious about your racing they should be glued to the rims.

   You should also have at least three different compounds (Soft, Medium and Hard) for varying track temperatures in On Road tarmac racing Touring cars and varying pin sizes for carpet and Off Road racing Buggys and Trucks.


How to Mount Rubber Tires onto Wheels/Rims.

   Before mounting your Tires, I would recommend talking to the more experienced racers at your local club, as to what inserts they use. Even the top level racers rely on a bit of local knowledge on tracks they have never raced before.

1/   Once you have decided what inserts to use, position them inside the Tires ready to go onto the rims.

2/   You will need strong fingers to pull and maneuver the Tires over the rims, so you may need the help of an adult. I would recommend NOT using metal Tire levers or a spoon as they can not only damage the fragile plastic rims but can also put small tears in the rubber, that could cause problems later.
   The technique I recommend, is to first of all hook the Tire on one side of the rim, then using the thumb and forefinger, grip the Tire and pull it upwards and over into position around the middle of the wheel, then over to its final position on the far side so that the beading is seated in the spigot. then position the near side beading in the opposite spigot making sure the sponge (or rubber) insert is not trapped and positioned centrally.

3/   You have the option of either gluing or not gluing your tires in position. If the track you race at is not too grippy you can get away with it, but on high grip tracks there is the possibility the tire might pull away from the rim and ruin your race.
My recommendation is to glue them.
   Superglue is the thing to use. To do this, carefully pull the beading out of its seating, put on a spot of glue, then quickly push it back down. repeat this at least 6 times around each side of the wheel.
Superglue can be dangerous, so this is best done by an adult.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: