RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Toyota-Celica. ITEM #58248 FF02.
RCScrapyard Radio Controlled Models
Flags

Tamiya Toyota Celica - #58248 (Radio Controlled Model)

1/10 Scale Electric Touring Car - FF-02 Chassis:

  Released by Tamiya on September 28, 1999, this accurately crafted Toyota Celica was the last of the Tamiya FF-02 chassis based electric self assembly models. The lightweight Lexan polycarbonate body shell in this kit superbly recreates the cars sleek lines. Decals of the cars trim and Toyota badges are included in the kit.

Tamiya Toyota Celica - #58248 FF02

  Based on the M03 Chassis the Front Wheel Drive FF02 had a short extension to lengthen the wheelbase and was used in only 3 Tamiya Models. Parts and spares were readily available being the same in many respects to the popular M03 series.

  Like many Tamiya models produced in the 80s and 90s, the kit comes with nylon/plastic and sintered brass bush type bearings that after a short while, when dust and grit get into them, will abrade the metal drive shafts that spin in them - if you are building this kit to race seriously these should be replaced by steel ball bearings.

  The cross chassis mounted battery position and high centre of gravity made this configuration difficult to handle in comparison to its predecessor and was prone to excessive over-steer on tight cornering. Changing the friction type shocks for oil filled and tweaking spring stiffness did overcome this problem to some degree.


      Rating: 3.53.5 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya Toyota Celica #58248 FF-02 - Chassis
Tamiya Toyota Celica #58248 FF-02 Chassis
Tamiya Toyota Celica #58248 FF-02
Tamiya Toyota Celica #58248 FF-02 Body Shell

Buying a Used Tamiya Toyota Celica
Touring Car (and What to look for)


   Buying a used Tamiya Toyota Celica Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Toyota Celica is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Toyota Celica model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Toyota Celica Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Toyota Celica steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Toyota Celica is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Toyota Celica model and good racing.


For More on how to Setup your Touring Car, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks













Tamiya Toyota-Celica


Hints and Tips

Weight

   If you ever step up and enter a regional, national or international event in RC, you will find one specific rule concerning the weight of your car.

   At the time this article was written, the Minimum weight restrictions for 1:10 electric Touring Cars at different events, was between 1350g and 1500g. This includes your Motor, ESC, Receiver, Battery, Body Shell and the transponder.

   Out of the box you will find the majority of 1:10 Touring Cars, with everything onboard, are way over this Minimum weight and unless you are good enough to attract sponsors, getting your car down to anything approaching that minimum weight will be very expensive.

   There are things you can buy like micro ESC and Receivers. But Batteries and Motors are what they are and you have to work around them.

   To reduce the weight of your chassis, there are a number of things you can do. If the car you have is generally considered competitive enough, there are often carbon fibre main chassis, shock mounts and other alternative parts available, but they are expensive. And when the new version of your model comes out all the money you have spent is lost.

   The most cost effective weight reduction is the metal parts of your chassis. UJs, Drive and Pivot shafts and the like tend to vary from model to model, but turnbuckles can often be transferred and lengthened or shortened by using plastic ball connectors, so titanium is a consideration.

   Screw sets can also be transferred from car to car. Titanium screws and wheel nuts are always available, but there is a cheaper alternative Aluminium screws and nuts can reduce your cars weight cheaply, but be careful not to over-tighten them, aluminium is not as strong as titanium and can easily shear off if you are over zealous.

   Another weight reduction option is to drill holes along the base of the chassis. However, I do not recommend this. For one thing you are reducing the strength and making the chassis less rigid, but you are also raising the centre of gravity of your car, which can affect stability.

   If you do manage to get your car weight below the minimum allowed, this will give you an opportunity to add weight where you want it and lower the cars centre of gravity.

   One last tip: Knitting needles. When I first started in RC, money was tight and my dad came up with all kinds of ideas to reduce weight. He obtained a 3mm dye and found some of my mums old aluminium knitting needles that were just the right diameter. Having determined the length of the turnbuckles needed for my setup, he cut them to those lengths and threaded each end, so he could put plastic ball sockets on them. Adjusting them was a bit of a pain and they could be a bit fragile in crash situations, but they saved us lots of money over those early years.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Tires for RC Models

Rubber Tires:

   Rubber Tires ALWAYS should have either soft sponge or rubber inserts. They will not function as they should without them. And if you are totally serious about your racing they should be glued to the rims.

   You should also have at least three different compounds (Soft, Medium and Hard) for varying track temperatures in On Road tarmac racing Touring cars and varying pin sizes for carpet and Off Road racing Buggys and Trucks.


How to Mount Rubber Tires onto Wheels/Rims.

   Before mounting your Tires, I would recommend talking to the more experienced racers at your local club, as to what inserts they use. Even the top level racers rely on a bit of local knowledge on tracks they have never raced before.

1/   Once you have decided what inserts to use, position them inside the Tires ready to go onto the rims.

2/   You will need strong fingers to pull and maneuver the Tires over the rims, so you may need the help of an adult. I would recommend NOT using metal Tire levers or a spoon as they can not only damage the fragile plastic rims but can also put small tears in the rubber, that could cause problems later.
   The technique I recommend, is to first of all hook the Tire on one side of the rim, then using the thumb and forefinger, grip the Tire and pull it upwards and over into position around the middle of the wheel, then over to its final position on the far side so that the beading is seated in the spigot. then position the near side beading in the opposite spigot making sure the sponge (or rubber) insert is not trapped and positioned centrally.

3/   You have the option of either gluing or not gluing your tires in position. If the track you race at is not too grippy you can get away with it, but on high grip tracks there is the possibility the tire might pull away from the rim and ruin your race.
My recommendation is to glue them.
   Superglue is the thing to use. To do this, carefully pull the beading out of its seating, put on a spot of glue, then quickly push it back down. repeat this at least 6 times around each side of the wheel.
Superglue can be dangerous, so this is best done by an adult.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: