RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Subaru Impreza WRC Arai Version. ITEM #58270 TB-01.
RCScrapyard Radio Controlled Models
Flags

Tamiya Subaru Impreza WRC Arai Version - #58270 (Radio Controlled Model)

1/10 Scale Electric Rally Car - TB-01 Chassis:

  Released by Tamiya on November 21, 2000, this TB-01 Chassis based RC Model, is of the Subaru Impreza driven by Japanese driver, Toshihiro Arai, in the 2000 World Rally Championships (WRC).

  The Lexan Body Shell replicates in high detail the Impreza racing lines. A driver and Co-Pilot plus decals of the cars racing livery are also included in the kit.

Tamiya Subaru Impreza WRC Arai Version - #58270 TB-01

  Released in 2000 the TB-01 Chassis lasted only three years before it was superseded by the TB-02 and in that time, eight TB-01 based kits were released and later, in 2009, two XB Truggy models were introduced on a modified TB-01 Chassis.

  The Chassis was introduced as a mid to high end market option over the TA and successful entry level TL-01.

  The prop shaft drive on the TB-01 used splines instead of the conventional dog bones type which were prone to wear and become sloppy and inefficient. The spline drive was much more solid and wear was minimal.

  The kit comes with nylon/plastic and sintered brass bush type bearings that after a short while, when dust and grit get into them, will abrade the metal drive shafts that spin in them - if you are building this kit to race seriously these should be replaced by steel ball bearings.

  The Bathtub Chassis was well braced and with the Upper frame in place was extremely tough and rigid.

  Upgraded, with the full set of ball bearings and the stock oil filled shocks this car was a winner. Cornering was smooth and precise and when upgraded with an 11x2 motor acceleration was wild.

  For a beginner, the kit 540 motor is enough to learn the basics with this model and you will quickly progress, ready for something with a little more punch.


      Rating: 4.54.5 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya Subaru Impreza WRC Arai Version #58270 TB-01 - Chassis
Tamiya Subaru Impreza WRC Arai Version #58270 TB-01 Chassis
Tamiya Subaru Impreza WRC Arai Version #58270 TB-01
Tamiya Subaru Impreza WRC Arai Version #58270 TB-01 Body Shell

Buying a Used Tamiya Subaru Impreza WRC
Rally Car (and What to look for)


   Buying a used Tamiya Subaru Impreza WRC Electric Rally Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Rally Car you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Rally Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Subaru Impreza WRC is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Subaru Impreza WRC model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Subaru Impreza WRC Rally Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Rally Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Rally Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Rally Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Rally Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Subaru Impreza WRC steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Subaru Impreza WRC is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Rally Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Subaru Impreza WRC model and good racing.


For More on how to Setup your Rally Car, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Painting a Lexan Body Shell.

   Most RC Model kits come with an unpainted, clear Lexan plastic Body Shell you yourself must prepare and paint. This type of Body Shell is painted on the inside and special spray or brush on Polycarbonate Paints MUST be used.

   The beauty of this is you can go wild and show off your artistic ability, or simply choose your favourite colour and add some choice decals later.

   This article is for those who have never done this kind of thing before and need some basic guidance.


   Firstly, cut off the waste from the body shell with sharp scissors. If required finish off the rounded wheel arches with smooth sandpaper wrapped around a drinks can.

   Any holes for body posts must also be drilled before painting. Place the clear body shell over the model and adjust the posts so the shell is in the desired position. Where the posts touch the shell make a small dot with a marker pen.
Next, pierce small holes in the shell where the dots are from the inside. Place the shell on an old piece of wood and drill the post holes, again, from the inside.

   The next thing to do is clean it inside and out. Any small amount of impurity such as oil or grease could impair the adhesion of the paint.
For this, fill a bowl with water and use a small amount of washing up liquid with a soft sponge. Never use a scourer. Rinse well to ensure no residue remains.

   Most Body Shells come with a set of sticky back paper masks for the windows etc that are positioned on the inside. If not supplied, you will have to either make your own, or use masking tape. Run your thumb nail around the edges of each mask to ensure contact paint can creep into any open area and easily ruin your hard work, so please be vigilant.

   Tip: To protect against paint spilling out onto the outside of the body shell, use masking tape around the outside edges and wheel arches.

   Now you are ready to begin applying your paint. Find a well ventilated area and if spraying, use a breathing mask.
Three or four sprayed, or at least two brushed layers are recommended allowing around thirty minutes between layers.

   Once the paint is fully dry, to protect the paint from scratching, spray or brush over it with one or two layers of clear plastic varnish.

   When the varnish is completely dry, carefully remove the window masks. If necessary, use a modelling knife to lift an edge to grasp between your thumb and finger DO NOT RUSH.

   Decals can now be placed on your body shell. So they adhere better I recommend any square edges are rounded. This reduced the tendency for them to peel off.

For More Setup Information check out my Hints and Tips page.



My First National

   When I first started in RC, way back in the late 1980s, I would turn up to the weekly club meeting, with my Tamiya Boomerang, transmitter, two sets of crystals, a couple of batteries, a charger and a tool box with a wheel spanner and a few spares.
   It was three five minute qualifying rounds and a final and every month we would have a trophy meeting. The trophies were donated by a two of the older semi professional guys who basically ran the club and over the years had collected what must have been hundreds of trophies and had no space for them anymore. The lure of a trophy always brought out the "not as enthusiastic types" and the small church function room was always packed on those nights.
   About a year in, my collection of B final trophies was beginning to clutter my room and my dad bought me the new Tamiya Manta Ray. That was the big turning point in my RC career.
   From then on it was A finals all the way. Then one day in the summer of 1992 the club organisers (the semi pro guys) asked me if I would like to go to a BIG national meeting way down south in Malvern. I asked my dad and with a bit of prompting he said "why not".
   When we got to that meeting we found there were around a hundred competitors, with ten groups of ten. I was in group "H". and two of my friends who came down with us were in group "I" so were on just before me.
   I remember that first race like it was yesterday. It was a staggered start and I set off next to last. I had never raced on a proper outdoor dirt track before. My only experience was on indoor carpet, but my old Manta Ray took off like a bullet. Most of the others in my heat were rookies and by the end of the third lap I was up with the leader. He was good very good but I stuck to him like glue. Each twist, turn and jump brought me closer and closer, this guy was fast, but I was faster for a while anyway. A lap before the end my old over worked 1400mah battery, was struggling to give me what I needed to keep up with him and my buggy got slower and slower. I ended up third in that first race, but wasn't about to give up that easy.
   There was a shop at the meeting and straight after the race I nagged my dad to get me a new battery. In those days money was tight and normally before dad would spend anything he would consult my mum, but this time she wasn't there and after watching my performance in that race he didn't need much pushing to get me that badly needed new battery.
   Waiting for the second round seemed to take an age, but when it arrived I was pumped up and ready with steely determination. I was away third after finishing third in the first round, so my duel with the guy who beat me before carried on where it had left off. Two laps in and I was on his tail. He wasn't going to beat me this time. We lapped a couple of back markers and were quickly catching up to a third. He slipped past him in a flash, but when I moved in, the idiot drove straight into me, knocking my Manta Ray on its back. The marshal was oblivious to my plight. I shouted my head of but the marshals eyes were fixed on what I guess was the car of one of his friends in my race. The next thing I saw was my dad, bounding across the track like a gazelle, picking up my car, putting it on the track and giving me the thumbs up. I drove like the wind, passing car after car, slowly working back up to third, where I eventually finished.
   But it didn't end there. Because my dad had ran out onto the track, I was disqualified we pleaded our case and eventually were allowed to continue.
   The third round heat arrived. This time I wasn't going to let anything stop me. My focus was to win that race and beat that guy who had all the luck so far. Because of the previous race I set off last. Car after car was left in my wake, until once more it was me against him. Mano a mano, he saw it was me and he upped his game. Lap after lap we duelled for the lead. Coming into the very last lap I was a nose in front and pulling away. With each corner I could sense the battery was once again giving up and my car started to slow down. Corner after corner I could see him getting closer and closer. we got to the final straight and he was right on top of me breathing down my neck. I held my breath and jammed over the throttle leaver and just crossed the line before him I had won my first national heat race. and it wasn't to be the last.

For Car Setup Information check out our Hints and Tips page.







^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: