RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Street Rover. ITEM: #58522 DT-02
RCScrapyard Radio Controlled Models
Flags

Tamiya Street Rover - #58522 (Radio Controlled Model)

1/10 Scale Electric Buggy - DT-02 Chassis:

  Released by Tamiya on February 22, 2012, based on the DT-02 Chassis, the 2WD Street Rover is an on-road variant of the Sand Rover (#58500) that was released in 2011.

Tamiya Street Rover - #58522 - 1:10 Electric Buggy

  The 2WD DT-02 Chassis employs an orbital gear differential, 4-wheel independent double wishbones with coil spring over friction dampers. These should be replaced by oil filled dampers for improved handling.

  A hard resin plastic body shell, pre-painted in Candy Lime Green is supplied, along with a set of wide-tread on-road semi pneumatic front and rear rubber tires, mounted on sliver-plated wheels, an RS540 silver can electric motor, a TEU-104BK ESC and a full set of steel shielded ball bearings. Radio equipment, battery, charger and paint for the body shell are required to complete.

  To get the best from the DT-02 Chassis, it needs to be fine tuned to handle jumps under control and has enough grip to hug the corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our simple to understand, step by step procedure, will guide you to the best Set-up for your driving style.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya Street Rover #58522 DT-02 - Chassis
Tamiya Street Rover #58522 DT-02 Chassis
Tamiya DT-02 Chassis
Tamiya DT-02 Chassis - Front

Buying a Used Tamiya Street Rover
Buggy (and What to look for)


   Buying a used Tamiya Street Rover Electric Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Street Rover is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Street Rover model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Street Rover Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Buggy racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Street Rover steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Street Rover is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Buggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Street Rover model and good racing.


For More on how to Setup your Buggy, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks













★ Tamiya Street Rover ★
Tamiya Street Rover - #58522 - 1:10 Electric Model


Gear Differentials


   The Gear Differentials, commonly used in Tamiya Buggys, Trucks, Touring Cars, Monster Trucks and some of the early Tamiya Formula One and Le-Mans cars, are by design more robust than the high maintenance Ball Differentials.

   The configuration uses a main drive gear, fixed on each side of the drive axles and either three or four small metal orbital bevel gears, in a plastic gear housing, providing the drive to each side of the car when cornering, to allow the inside wheel to rotate slower than the outside wheel.

   Maintaining your Gear differentials is crucial if your car is to be competitive. Regular greasing is required, preferably molybdenum grease with graphite flakes, smeared over the gear teeth. If neglected, the gear teeth grind and wear at a rapid rate and will quickly fail, leaving you with a potentially expensive rebuild.

   For slower moving models such as Monster Trucks, Rock Crawlers and budget end Off road Buggys, Trucks and On Road Drift and Touring Cars, where low friction differential action is not essential, Gear Differentials are ideal, providing drive to each wheel as required. However, for top level competitive racing ,On and Off Road, Ball Differentials are preferable. Admittedly, they require a little more maintenance, but the benefits on the track far outweigh the negatives of the old Gear diffs.

For More Setup Information check out my Hints and Tips page.



Hints and Tips


Electric Motors for RC Models

Brushless Motor Basics

   Choosing the right Brushless motor for your needs can be a daunting task for those new to Radio Controlled Models. If you have a local club perhaps you could ask some of the more experienced members for their advice, but a little basic knowledge about the subject, so you know what questions to ask is always useful.

   All Brushless motors are rated by Kilovolts (KV) and is an indication of the revs per minute (RPM) that particular Motor can attain running freely, under no load conditions, per Volt of input.

   For Example: To calculate the Maximum RPM of a Motor listed at 4000 KV, connected to a 7.4 Volt Battery, simply multiply the two: 4000 x 7.4 = 29600 RPM.

   The two main types of Brushless Motors used in RC are Sensored and a Sensorless Motors.
   Sensored Motors can be connected directly using s cable, to the Electronic Speed Controller (ESC). The ESC is then able to monitor the performance of the Motor and regulate Current output, to attain smooth, controlled acceleration. Advance and Retard timing is made automatically by the ERSC to change torque when exiting corners and give you more RPM for long straights.

   Sensorless Motors can only be set manually for Advance and Retard timing and once that setting is made you have to stick with it. For obvious reasons, Sensorless motors are cheaper to buy than the Sensored type: Ideal if you just want to bash around in the back yard, but not so much if you are serious about your racing.

   Brushless Motors, need a reasonable amount of maintenance if they are to remain competitive. For top level racing I recommend you strip, clean and re-oil the bearings every 2 or 3 meetings (Check out our "get the best from your bearings" section).
   Gearing your motor correctly for any given track is always important. (Check out my Gearing tips on the Pinions Section of this site) A cool motor is an efficient motor. As your motor heats up towards the end of a race, it will loose efficiency. Gearing correctly can avoid this problem to some degree and simply following my simple guidelines, described in the aforementioned article can help you not only keep your motor running efficiently, but help you stay in front of your opposition.

   One last tip .. When re-building your Brushless Motor, to safely replace the Rotor, use a rolled up piece of paper and place it into the Can. This will protect your rotor against damage. Then carefully remove the paper before replacing the endbell.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: