RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Monster Beetle 2015. ITEM: #58618
RCScrapyard Radio Controlled Models
Flags

Tamiya Monster Beetle 2015 - #58618 (Radio Controlled Model)

1/10 Scale Electric RC Monster Truck - ORV Chassis:

  Released by Tamiya on November 14, 2015, based on the original 1986 Monster Beetle, the 2015 version has an updated chassis allowing for modern day electronics to be installed.

Tamiya Monster Beetle - #58618

  Like the original, the new model comes with a gear type differential, coil spring over oil filled dampers, a silver can 540 motor and spike ribbed tires, along with a TBLE-02S ESC with reverse.

  The low centre of gravity is as ever, ideal for power slides, jumps and sideways fun for all age groups.

  But it's the instantly recognisable Beetle bodyshell that makes the model standout from the crowd. The detail Tamiya put into the injection molded hard plastic Monster Beetle shell is once again a work of art.

  For collectors, the new Monster Beetle may fill any large empty space in the display cabinet and look almost indistinguishable to the original, but for those hard core collectors, do not despair; original models are still out there, tucked away in the garage, the basement, or up in the attic, just waiting to be re-discovered.


      Rating: 3.53.5 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya Monster Beetle 2015 #58618 - Chassis
Tamiya Monster Beetle 2015 #58618 Chassis
Tamiya Monster Beetle 2015 #58618 - Chassis
Tamiya Monster Beetle 2015 #58618 Chassis

Buying a Used Tamiya Monster Beetle
Monster Truck (and What to look for)


   Buying a used Tamiya Monster Beetle Electric Monster Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Monster Truck you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Monster Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Monster Beetle is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Monster Beetle model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Monster Beetle Monster Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Monster Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Monster Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Monster Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Monster Truck racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Monster Beetle steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Monster Beetle is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Monster Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Monster Beetle model and good racing.


For More on how to Setup your Monster Truck, check out my Hints and Tips page.














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Tires for RC Models

Rubber Tires:

   Rubber Tires ALWAYS should have either soft sponge or rubber inserts. They will not function as they should without them. And if you are totally serious about your racing they should be glued to the rims.

   You should also have at least three different compounds (Soft, Medium and Hard) for varying track temperatures in On Road tarmac racing Touring cars and varying pin sizes for carpet and Off Road racing Buggys and Trucks.


How to Mount Rubber Tires onto Wheels/Rims.

   Before mounting your Tires, I would recommend talking to the more experienced racers at your local club, as to what inserts they use. Even the top level racers rely on a bit of local knowledge on tracks they have never raced before.

1/   Once you have decided what inserts to use, position them inside the Tires ready to go onto the rims.

2/   You will need strong fingers to pull and maneuver the Tires over the rims, so you may need the help of an adult. I would recommend NOT using metal Tire levers or a spoon as they can not only damage the fragile plastic rims but can also put small tears in the rubber, that could cause problems later.
   The technique I recommend, is to first of all hook the Tire on one side of the rim, then using the thumb and forefinger, grip the Tire and pull it upwards and over into position around the middle of the wheel, then over to its final position on the far side so that the beading is seated in the spigot. then position the near side beading in the opposite spigot making sure the sponge (or rubber) insert is not trapped and positioned centrally.

3/   You have the option of either gluing or not gluing your tires in position. If the track you race at is not too grippy you can get away with it, but on high grip tracks there is the possibility the tire might pull away from the rim and ruin your race.
My recommendation is to glue them.
   Superglue is the thing to use. To do this, carefully pull the beading out of its seating, put on a spot of glue, then quickly push it back down. repeat this at least 6 times around each side of the wheel.
Superglue can be dangerous, so this is best done by an adult.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Your First Race Meeting

   When you finally find a racing club near to where you live, that initial experience of stepping up onto the rostrum and looking down over the track can be very daunting. But soon, as the race starts, adrenaline will kick in and away you go. For the next five minutes, your focus is on nothing but getting your car around each corner, avoiding all the other cars on the track and just getting to the end of the race.

   Maybe your batteries dumped or you crashed and the car was damaged, perhaps you didn't actually come last, whatever happened, it doesn't really matter you are well and truly hooked.

   When the race is over, don't be afraid to ask the more experienced racers questions about setup, driving tips etc. They have all been where you are now and will be more than willing to help you. Show them your car, get some tips on tires, gearing and general set-up for the club track.

   Then, when you get back home, go through all your races in your mind. Try to identify the things you did wrong and figure out how to avoid those mistakes next time. Think about what all the more experienced racers told you and change your settings as they advised.

   Put down a few buckets or cones in the back yard to practice driving round, something that if you hit it won't damage your car. Get someone to time you for say ten laps and each day after school, try to beat that time. The adage, "Practice makes perfect" holds true in many things, not least the sport of RC racing and as your confidence increases, your racing skills improve and the trophies begin to line up on your bedroom shelf, you will one day yourself be the guy all the newbie's look to for advice and you will remember that day, you nervously stepped up onto that platform for the first time, looked down across the track and how your whole life changed in that fleeting moment.

For More Setup Information check out my Hints and Tips page.








^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: