RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Mitsubishi Lancer Evolution V WRC. ITEM #58225 TA-03F.
RCScrapyard Radio Controlled Models
Flags

Tamiya Mitsubishi Lancer Evolution V WRC - #58225 (Radio Controlled Model Review)

1/10 Scale Electric Rally Car - TA-03F Chassis:

  Released by Tamiya on November 12, 1998, this TA-03F Chassis based, self assembly electric RC model, is of the Factory Team Mitsubishi Lancer Evolution V that Tommi Makinen drove to win the 1998 World Rally Championship (WRC).

  The lightweight Lexan polycarbonate body shell in this kit is an accurate copy of the cars classic lines. Decals of the livery are included in the kit.

Tamiya Mitsubishi Lancer Evolution V WRC - #58225 TA-03F
▼ Scroll Down for More Images ▼


  The Four Wheel Drive, front mounted motor, TA03F chassis, uses a single belt drive system, with orbital Bevel Gear differentials front and rear. These were upgraded for the Pro spec models to Ball differentials. The suspension is four wheel independent double wishbone with Coil Spring over Oil Filled shock absorbers.

  Because of the front mounted motor and the transversely mounted stick battery towards the rear of the chassis, the weight distribution made the handling of this model to be somewhat different to the previous Tamiya TA designs. Body roll and under-steer could be controlled by adjusting the tuning springs and oil weight in the shocks, but the fixed shock mount positioning made this adjustment difficult for some tracks.

  The original TA03F kit comes with plastic/nylon and sintered brass bush type bearings that after a short while, when dust and grit get into them, actually wear into the metal drive shafts - if you are building this kit to race seriously these should be replaced by steel ball bearings.

  In conclusion. With the right set-up, tires and a full set of ball bearings, the TA03F in the right hands could be a winner.


      Rating: 3.53.5 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:














Flags

Tamiya Mitsubishi Lancer Evolution V WRC #58225 TA-03F - Chassis
Tamiya Mitsubishi Lancer Evolution V WRC #58225 TA-03F Chassis
Tamiya Mitsubishi Lancer Evolution V WRC #58225 TA-03F
Tamiya Mitsubishi Lancer Evolution V WRC #58225 TA-03F Body Shell

Buying a Used Tamiya Mitsubishi Lancer Evolution V WRC
Rally Car (and What to look for)


   Buying a used Tamiya Mitsubishi Lancer Evolution V WRC Electric Rally Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Rally Car you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Rally Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Mitsubishi Lancer Evolution V WRC is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Mitsubishi Lancer Evolution V WRC model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Mitsubishi Lancer Evolution V WRC Rally Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Rally Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Rally Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Rally Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Rally Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Mitsubishi Lancer Evolution V WRC steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Mitsubishi Lancer Evolution V WRC is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Rally Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Mitsubishi Lancer Evolution V WRC model and good racing.




▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks













Tamiya Mitsubishi-Lancer-Evo


My First National

   When I first started in RC, way back in the late 1980s, I would turn up to the weekly club meeting, with my Tamiya Boomerang, transmitter, two sets of crystals, a couple of batteries, a charger and a tool box with a wheel spanner and a few spares.
   It was three five minute qualifying rounds and a final and every month we would have a trophy meeting. The trophies were donated by a two of the older semi professional guys who basically ran the club and over the years had collected what must have been hundreds of trophies and had no space for them anymore. The lure of a trophy always brought out the "not as enthusiastic types" and the small church function room was always packed on those nights.
   About a year in, my collection of B final trophies was beginning to clutter my room and my dad bought me the new Tamiya Manta Ray. That was the big turning point in my RC career.
   From then on it was A finals all the way. Then one day in the summer of 1992 the club organisers (the semi pro guys) asked me if I would like to go to a BIG national meeting way down south in Malvern. I asked my dad and with a bit of prompting he said "why not".
   When we got to that meeting we found there were around a hundred competitors, with ten groups of ten. I was in group "H". and two of my friends who came down with us were in group "I" so were on just before me.
   I remember that first race like it was yesterday. It was a staggered start and I set off next to last. I had never raced on a proper outdoor dirt track before. My only experience was on indoor carpet, but my old Manta Ray took off like a bullet. Most of the others in my heat were rookies and by the end of the third lap I was up with the leader. He was good very good but I stuck to him like glue. Each twist, turn and jump brought me closer and closer, this guy was fast, but I was faster for a while anyway. A lap before the end my old over worked 1400mah battery, was struggling to give me what I needed to keep up with him and my buggy got slower and slower. I ended up third in that first race, but wasn't about to give up that easy.
   There was a shop at the meeting and straight after the race I nagged my dad to get me a new battery. In those days money was tight and normally before dad would spend anything he would consult my mum, but this time she wasn't there and after watching my performance in that race he didn't need much pushing to get me that badly needed new battery.
   Waiting for the second round seemed to take an age, but when it arrived I was pumped up and ready with steely determination. I was away third after finishing third in the first round, so my duel with the guy who beat me before carried on where it had left off. Two laps in and I was on his tail. He wasn't going to beat me this time. We lapped a couple of back markers and were quickly catching up to a third. He slipped past him in a flash, but when I moved in, the idiot drove straight into me, knocking my Manta Ray on its back. The marshal was oblivious to my plight. I shouted my head of but the marshals eyes were fixed on what I guess was the car of one of his friends in my race. The next thing I saw was my dad, bounding across the track like a gazelle, picking up my car, putting it on the track and giving me the thumbs up. I drove like the wind, passing car after car, slowly working back up to third, where I eventually finished.
   But it didn't end there. Because my dad had ran out onto the track, I was disqualified we pleaded our case and eventually were allowed to continue.
   The third round heat arrived. This time I wasn't going to let anything stop me. My focus was to win that race and beat that guy who had all the luck so far. Because of the previous race I set off last. Car after car was left in my wake, until once more it was me against him. Mano a mano, he saw it was me and he upped his game. Lap after lap we duelled for the lead. Coming into the very last lap I was a nose in front and pulling away. With each corner I could sense the battery was once again giving up and my car started to slow down. Corner after corner I could see him getting closer and closer. we got to the final straight and he was right on top of me breathing down my neck. I held my breath and jammed over the throttle leaver and just crossed the line before him I had won my first national heat race. and it wasn't to be the last.

For Car Setup Information check out our Hints and Tips page.

Hints and Tips

Tires for RC Models

Rubber Tires:

   Rubber Tires ALWAYS should have either soft sponge or rubber inserts. They will not function as they should without them. And if you are totally serious about your racing they should be glued to the rims.

   You should also have at least three different compounds (Soft, Medium and Hard) for varying track temperatures in On Road tarmac racing Touring cars and varying pin sizes for carpet and Off Road racing Buggys and Trucks.


How to Mount Rubber Tires onto Wheels/Rims.

   Before mounting your Tires, I would recommend talking to the more experienced racers at your local club, as to what inserts they use. Even the top level racers rely on a bit of local knowledge on tracks they have never raced before.

1/   Once you have decided what inserts to use, position them inside the Tires ready to go onto the rims.

2/   You will need strong fingers to pull and maneuver the Tires over the rims, so you may need the help of an adult. I would recommend NOT using metal Tire levers or a spoon as they can not only damage the fragile plastic rims but can also put small tears in the rubber, that could cause problems later.
   The technique I recommend, is to first of all hook the Tire on one side of the rim, then using the thumb and forefinger, grip the Tire and pull it upwards and over into position around the middle of the wheel, then over to its final position on the far side so that the beading is seated in the spigot. then position the near side beading in the opposite spigot making sure the sponge (or rubber) insert is not trapped and positioned centrally.

3/   You have the option of either gluing or not gluing your tires in position. If the track you race at is not too grippy you can get away with it, but on high grip tracks there is the possibility the tire might pull away from the rim and ruin your race.
My recommendation is to glue them.
   Superglue is the thing to use. To do this, carefully pull the beading out of its seating, put on a spot of glue, then quickly push it back down. repeat this at least 6 times around each side of the wheel.
Superglue can be dangerous, so this is best done by an adult.

For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: