RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya McLaren MP4/6 Honda. Item #58104.
RCScrapyard Radio Controlled Models
Flags

Tamiya McLaren MP4/6 Honda - #58104 (Radio Controlled Model)

1/10 Scale Electric Formula One Car - F102 Chassis:

  Released by Tamiya on March 10, 1992, this model is based on the McLaren MP4/6 Honda that was driven by Ayrton Senna to win the 1991 Formula One world championship.

Tamiya McLaren MP4/6 Honda - #58104 F102

  This was the first Tamiya Formula One car to employ the replacement for the F101 chassis, the F102.

  With redesigned narrower chassis for reduced rigidity, cut down T-bar plate and simplified rear wheel thrust bearing installation, the F102 chassis performed well. The more flexible design did, to some degree, improve handling.

  I used three different sponge tire compounds when I raced 1:10 Scale F1, plus a set of wet weather slicks. Tire wear was always a problem due to the simple fact the smaller the wheel diameter the lower the ground clearance. New sponges were needed after every two or three outdoor meetings.

  If you intend racing your McLaren MP4/6 Honda car competitively I would recommend changing the kit supplied plastic and sintered brass bush type bearings for steel ball bearings. The improved performance is well worth the expense.


      Rating: 3.53.5 Stars out of 5 Reviewed by: RCScrapyard     Manual.





Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya McLaren MP4/6 Honda #58104 F102 - Chassis
Tamiya McLaren MP4/6 Honda #58104 F102 Chassis
Tamiya McLaren MP4/6 Honda #58104 F102
Tamiya McLaren MP4/6 Honda #58104 F102 Body Shell

General Information and Advice

   For those starting in Radio Controlled Racing, here are a few Hints and Tips: Firstly, buy a Kit not an RTR. That way, if something breaks you will have some idea how to fix it.

   Radio Controlled Model Cars are very fragile and easily broken. The main parts to protect are the Front Wishbones, Suspension Shock Towers, Dampers, Hub Carriers, Kingpins, Uprights and Toe in Blocks, so make sure you have a good strong front bumper and Lexan or Hard Plastic Body Shell and if available for your model, a protective under tray, to prevent grit and dust getting into any moving parts.

   The Steering Servo is also a weakness in high speed crash situations, so get yourself some good strong Servo Mount and Servo Saver. Also I would recommend Titanium Shafts, Turnbuckles, Tie Rods and pivot/steering shafts and if available for your model, lightweight Titanium Drive shafts, dog bones and CVD (Constant Velocity Drives). The standard steel types are far too easily bent.

   Gearing is another problem area on RC model cars. Head on collisions can easily break off gear teeth on Nylon/Plastic Spur Gears and even Bevel Gears inside the Gearbox. Heavy impacts can also loosen nuts and self taping screws that hold the Motor in Position, allowing the Pinion Gear to pull out of mesh slightly and rip the tops of the teeth on your Spur Gear. To avoid this to some degree, fit locking nuts and a new motor mount from time to time, so the self taping screws that hold the motor in position have less chance to come loose.

   Ball joints always cause problems. For top level Radio Controlled model car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector breaking free could easily end your race, so better safe than sorry.

   Many New car kits come with Nylon and Sintered Brass Ring type bearings. My advice is to discard these before initial installation and buy a good Hop-up set of Shielded Steel Ball Bearings. Or if you are serious about your racing, Teflon or Ceramic Bearings.

   One final piece of advice about the Setup of your Car. Keep the Centre of Gravity as low as possible. Ride Height is all important. For On Road Drift/Touring cars the Ride Height should be no more than 5mm, for Buggys, Trucks, Truggys and Monster Trucks, as low as possible depending on the track conditions. If Body Roll is a problem, handling can be improved with the use of Stabilizers, Anti roll or Sway Bars, stiffer Tuning Springs and, or thicker Silicon Oil in the Dampers. Also find somewhere to mount the Transponder as low in the Chassis as possible.

For Car Setup Information check out our Hints and Tips page.













^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips

Soldering Battery Packs

   Nicad and Nimh batteries sometimes come as six separate matched 1.2 volt cells. These of course have to be soldered to each other in series to produce either a side by side stick pack, or a two times three cell saddle pack.

   Special copper, or silver plated straps must be used to make up these packs and each strap must be prepared before attempting to solder it to the battery cell, by placing a blob of solder at each end of all the straps needed.

   A jig to hold the cells vertical and side by side is advisable. Using electrical solder, with a flux core (flux aids the flow and adhesion of the solder) heat your soldering iron to as hot as it will go. Then with the stick of solder touching on the end of the cell, touch it with the iron. What you want it to spread evenly on the central part of the pole of the cell. Count to 3 seconds. If it doesn't melt the solder in that time, your iron is not hot enough. Battery cells are notoriously very fragile and susceptible to the very high temperatures soldering requires. Anything longer than four or five seconds direct contact with the iron can cause damage to the crystal structure in the cell, so be wary.

   When you have solder on each end of each cell, line them up in the jig, positive to negative and dab a spot of flux on the soldered cells, then position your straps, with the solder coated side faced down, touching the solder on the end of the cell. Now place your hot iron on the strap. Heat will transfer through the strap and melt the solder on the two faces. Again, count to 3 and you should feel the strap drop slightly as the solder fuses with the solder on the cell. Repeat this for each cell on both sides to produce your desired configuration. Finally solder your two wires, previously prepared with connectors, to the pack. Do not solder wires with bare ends to your pack. If these wires were to touch and short out, you could effectively kill your expensive battery pack I use Red for positive and Black for negative, but so long as you know which is which electrical equipment does not like the battery to be connected the wrong way.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Tires for RC Models

Sponge (Foam) Tires:

   Sponge Tires can be purchased either pre mounted, glued and trued on the rims, or separately. Fitting the Tires onto the rims can be messy, so here are a few tips to make it a bit easier.
   If you are fitting new Tires on old rims, make sure the old sponge Tire is completely removed. To do this, I recommend using a wood lathe and apiece of wood, at least 300mm long and more than the width of your wheels, with medium grit emery paper stuck to it ... sand paper will also work, but emery is harder wearing ... This will also be used for truing a wheel. (Described later)

How to Mount and Glue Sponge Tires onto Wheels/Rims.

1/   Mount the Tires on the rims. Make sure they are reasonably tight on the rims, too loose and you might have problems.

2/   I find this to be easier if either in the lathe, or on the car itself. (but be careful with that glue)
  Using your thumb and forefinger, lift up the Tire off the rim, then using a small spatula or a thin piece of rigid wood or plastic dipped in glue (I recommend Evo-Stik, Impact Adhesive) slip it in the gap, making sure both the Tire and the rim are smeared. Then lower the Tire back onto the rim and press it down. Turn the Tire approximately 60 degrees and repeat.

3/   Depending on the width of the Tire you may need to repeat the process on the inside also.


How to True Sponge Tires.

   Truing Sponge Tires is essential if you are serious about racing competitively. To do this you will need the piece of wood, as described earlier and a good pair of vernier or digital calipers.
   Sponge Tires will always wear unevenly, weather you race on Carpet or Tarmac. The outside wheels will always end a race smaller than the ones on the inside, so after each race I recommend swapping them over (unless you are fortunate to have a new set for each race) and dont forget to adjust the steering trim on your transmitter before the next race.

1/   Before starting, check each mounted Tire for diameter and order them smallest to largest. Start with the smallest and mount it in the lathe.

2/   Make sure you are wearing safety glasses before you start this procedure: Lay the sanding wood under the Tire so that it can be pivoted up from behind onto the Tire. Start the lathe spinning, so that as you stand infront of the Tire, it is rotating downwards. Slowly lift the sanding wood and try to hold it ridged as it comes up against the Tire. There will be a high point on the Tire that if you hold the bat rigid enough will eventually wear down until the Tire appears completely concentric. at this point stop the lathe and measure the diameter on the inside and outside of the width. If needs be, repeat the process until satisfied.
Repeat for each Tire, matching them in pairs for diameter.
If considered necessary also trim the sides.


For More Setup Information check out my Hints and Tips page.









^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: