RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya Boomerang 2008. ITEM: #58418
RCScrapyard Radio Controlled Models
Flags

Tamiya Boomerang 2008 - #58418 (Radio Controlled Model Review)

1/10 Scale Electric Buggy - BMR Chassis:

  Released by Tamiya on December 10, 2008, 22 years after the original Boomerang (#58055), first released in 1986, Tamiya have produced a new version of the much loved 4WD off road Buggy.

Tamiya Boomerang 2008 - #58418
▼ Scroll Down for More Images ▼


  The distinctive style of the Boomerang has not been altered, but certain improvements have been made in an attempt to make the car more competitive, including an improved gearbox and a polycarbonate cover to prevent dirt and dust clogging up the parts.

  Many of the original models parts remain, including; the orbital bevel gear differentials, coil spring over oil filled shock absorbers, the poorly designed front upright steering configuration and the awkward plate spacers for pinion to spur gear clearance.

  Although some ball bearings are now included in the kit, the majority are the old plastic and sintered brass bush type bearings that, when dust and grit get into them, will abrade the drive shafts that spin in them. My tip is to replace these with steel shielded ball bearings before initial assembly.

  Drivers of the original feel this car is a great improvement and are pleased to note that the true spirit of the Boomerang has not be lost in this new version.


      Rating: 33 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:











Flags

Tamiya Boomerang 2008 #58418 - Chassis
Tamiya Boomerang 2008 #58418 Chassis
Tamiya Boomerang 2008 #58418
Tamiya Boomerang 2008 #58418 Body Shell

Buying a Used Tamiya Boomerang
Buggy (and What to look for)


   Buying a used Tamiya Boomerang Electric Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

Dampers
   When you receive your used Tamiya Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya Boomerang is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Boomerang model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Boomerang Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Buggy racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The Boomerang steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya Boomerang is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Buggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Boomerang model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Gear Differentials


   The Gear Differentials, commonly used in Tamiya Buggys, Trucks, Touring Cars, Monster Trucks and some of the early Tamiya Formula One and Le-Mans cars, are by design more robust than the high maintenance Ball Differentials.

   The configuration uses a main drive gear, fixed on each side of the drive axles and either three or four small metal orbital bevel gears, in a plastic gear housing, providing the drive to each side of the car when cornering, to allow the inside wheel to rotate slower than the outside wheel.

   Maintaining your Gear differentials is crucial if your car is to be competitive. Regular greasing is required, preferably molybdenum grease with graphite flakes, smeared over the gear teeth. If neglected, the gear teeth grind and wear at a rapid rate and will quickly fail, leaving you with a potentially expensive rebuild.

   For slower moving models such as Monster Trucks, Rock Crawlers and budget end Off road Buggys, Trucks and On Road Drift and Touring Cars, where low friction differential action is not essential, Gear Differentials are ideal, providing drive to each wheel as required. However, for top level competitive racing ,On and Off Road, Ball Differentials are preferable. Admittedly, they require a little more maintenance, but the benefits on the track far outweigh the negatives of the old Gear diffs.

For More Setup Information check out my Hints and Tips page.



Hints and Tips

Servo Information

   Servos are found on all kinds of Radio Controlled Models. RC Touring Cars, Buggys, Trucks, Truggys, Monster Trucks, Rock Crawlers, Airplanes, Helicopters, Boats and Ships for Steering, Throttle Control, Rudder Operation and Wing Flaps.

   For complete RC beginners, choosing the right servo can be confusing, so here are a few tips to point you in the right direction.

   The standard, plastic bushed (bearings) type servos are fine to start with but come with plastic/nylon gears that can break easily in collisions. So, to protect your servo gears to some degree, make sure you have a good "servo saver".

   Servo Savers come in a number of forms and are often included as standard on some RC Models. The best ones, in my opinion, are those that use a small spring to absorb the shock of the crash and are simply fitted in place of the servo horn.

   For lightweight, small scale models, plastic geared servos are fine. But for medium to large scale RC models, I would recommend metal or titanium gear servos. These servos are by nature heavier and more costly than the plastic geared ones but are well worth the extra expense, for obvious reasons.

   Digitally controlled Servos use a microprocessor based controller board. They are generally faster, provide better torque and centralise more accurately than the older Analogue types, but again at a higher cost.

   As you advance in experience and skill, you might feel the need for something to match your lightning reflexes. Mos-FET, or simply FET Servos use Ball bearings and will provide the high speed response you crave, but at a price. However, if your budget will stretch to the higher cost, the improvement in performance can make a big difference.

For More Setup Information check out my Hints and Tips page.







^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: