RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Yokomo YZ-10 - Team Associated - 1988.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Electric Buggy:

Yokomo YZ-10 - Team Associated - 1988 (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Yokomo

All Manufacturers: Model Types  >  Buggys  >  1/10 Electric Buggys

History, Info (and How To Set-up Tips) for the Yokomo YZ-10:


  Manufactured by Team Yokomo in 1988, the 4WD YZ-10 buggy, was produced for Team Associated for distribution in the USA.

  The model was basically a YZ-870c Super Dogfighter, with a new Protech bodyshell and wheels.

  The YZ-10 design was belt driven, on a graphite plate chassis, with ball differentials, improved coil spring over oil filled dampers, universal joint drive-shafts and a full set of ball bearings.

Yokomo YZ-10 - 1:10 Electric Buggy
▼ Scroll Down for More Images ▼


  To race the Yokomo YZ-10, it calls for fine tuning to attain better steering response and improve grip when cornering so you don't slide off the side of the track. Minute changes can make huge advancements. Our easy to understand list will show you how and lead you to the optimum Set-up to put you in front of the rest on the track.

  We give you all the basic information you need to guide you to the best Electric Motor for your YZ-10 and achieve the best Gearing, to get you in front on the track and keep you there.

  Find out how the worlds top professional RC racers get improved efficiency from their Bearings employing a number of sensible ideas. Find the way to avoid Radio interference, and basic instruction on how to Charge your Batteries, so they will last longer and provide improved power.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Yokomo - Associated - YZ-10 1988 ★
Yokomo - Associated - YZ-10 1988

★ Yokomo - Associated - YZ-10 1988 Chassis ★
Yokomo - Associated - YZ-10 1988 Chassis

★ Yokomo - Associated - YZ-10 1988 Chassis ★
Yokomo - Associated - YZ-10 1988 Chassis

★ Yokomo - Associated - YZ-10 1988 Chassis ★
Yokomo - Associated - YZ-10 1988 Chassis

★ Yokomo - Associated - YZ-10 1988 Chassis ★
Yokomo - Associated - YZ-10 1988 Chassis


Buying a Used Yokomo YZ-10 Buggy (and What to look for)


   Buying a used Yokomo YZ-10 Electric Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Yokomo website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

Dampers
   When you receive your used Yokomo Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Yokomo models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Yokomo YZ-10 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your YZ-10 model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your YZ-10 Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

Spur Gears
   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The YZ-10 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Yokomo YZ-10 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Yokomo Buggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your YZ-10 model and good racing.


For More on how to Setup your Buggy, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Tire Compounds

   Way back in the early 1990s when I first got into RC, most of the off-road models available came with chunky hard compound block tires that gave little or no grip on grass or dirt tracks. On-road didn't have this problem as they were still using sponge tires that with a coating of wintergreen based tire additive before each race to improve grip. There was even one guy who swore, before every race, he dipped his wheels in a glass of light ale.

   Then things started to change. By the mid 1990s tire manufacturers such as Losi and Schumacher began developing smaller pin tires, in softer compounds. These mini pin versions were a revelation for grass racers, but were only a small improvement on dust tracks.

   As new compounds were released, grip slowly improved. Then, with the release of the micro pin, super soft compound tires, off road was a completely different sport. Grip roll was now one of the problems drivers had to learn to contend with. This was something unheard of only a few short years before.

   Rubber Tires for On-road RC models had been around for a while in the early 1990s, but because sponge was so widely used, rubber never really caught on. Then, as Tamiya released its 1:10 on road models based on the off-road Manta Ray chassis, other manufacturers caught on and began producing their own 1:10 on-road cars. Schumacher released the SST 98, using the same gearbox and differentials as their Cat 2000 to reduce tooling costs. Tires were now being produced for this new scale in rubber. Pit Shimizu and Take-off were two of the leading RC on-road tire developers at the time, each releasing three different compounds, with recommended track temperature use. From that point on, on-road RC racing never looked back and the days of sponge and light ale came to a shuddering stop.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Painting a Lexan Body Shell.

   Most RC Model kits come with an unpainted, clear Lexan plastic Body Shell you yourself must prepare and paint. This type of Body Shell is painted on the inside and special spray or brush on Polycarbonate Paints MUST be used.

   The beauty of this is you can go wild and show off your artistic ability, or simply choose your favourite colour and add some choice decals later.

   This article is for those who have never done this kind of thing before and need some basic guidance.


   Firstly, cut off the waste from the body shell with sharp scissors. If required finish off the rounded wheel arches with smooth sandpaper wrapped around a drinks can.

   Any holes for body posts must also be drilled before painting. Place the clear body shell over the model and adjust the posts so the shell is in the desired position. Where the posts touch the shell make a small dot with a marker pen.
Next, pierce small holes in the shell where the dots are from the inside. Place the shell on an old piece of wood and drill the post holes, again, from the inside.

   The next thing to do is clean it inside and out. Any small amount of impurity such as oil or grease could impair the adhesion of the paint.
For this, fill a bowl with water and use a small amount of washing up liquid with a soft sponge. Never use a scourer. Rinse well to ensure no residue remains.

   Most Body Shells come with a set of sticky back paper masks for the windows etc that are positioned on the inside. If not supplied, you will have to either make your own, or use masking tape. Run your thumb nail around the edges of each mask to ensure contact paint can creep into any open area and easily ruin your hard work, so please be vigilant.

   Tip: To protect against paint spilling out onto the outside of the body shell, use masking tape around the outside edges and wheel arches.

   Now you are ready to begin applying your paint. Find a well ventilated area and if spraying, use a breathing mask.
Three or four sprayed, or at least two brushed layers are recommended allowing around thirty minutes between layers.

   Once the paint is fully dry, to protect the paint from scratching, spray or brush over it with one or two layers of clear plastic varnish.

   When the varnish is completely dry, carefully remove the window masks. If necessary, use a modelling knife to lift an edge to grasp between your thumb and finger DO NOT RUSH.

   Decals can now be placed on your body shell. So they adhere better I recommend any square edges are rounded. This reduced the tendency for them to peel off.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: