RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Yokomo YZ-834B Wonder Dog Fighter.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Electric Buggy:

Yokomo YZ-834B Wonder Dog Fighter (Radio Controlled Model Review)


Navigation: Sitemap  ▶  Manufacturers  ▶  Yokomo

History, Info (and How To Set-up Tips) for the Yokomo YZ-834B Wonder Dog Fighter:


  Introduced by Team Yokomo circa 1985, the 4WD YZ-834B Wonder Dog Fighter, went on to win the 1985 World Championship in Pomona California, driven by Gil Losi Jr.

  The model is chain driven, on a thicker FRP double deck chassis, with a rear ball differential, torque limiter, front mono-shock, with rear dual coil spring over oil filled dampers and rear anti roll bar.

  A YZ-834B Wonder Dog Fighter Limited Edition was also produced, supplied with a 360SX Twin Turbo motor and in 1986 a YZ-834B Wonder Dog Fighter Special Edition (SE) was released, with Super Aero wheels and Hot Laps R-5 2 inch tires, later in the same year the model was replaced with the YZ-834B Wonder Dog Fighter RPS SE, with a new bodyshell, improved dampers and 1.75 inch yellow wheels with Pro-Line RPS tires.

  Two versions were available, the SE10 Standard kit and SE11 Deluxe kit, with NBM ball bearings.

Yokomo Wonder Dog Fighter - 1:10 Electric Buggy
▼ Scroll Down for More Images ▼


  To race the Yokomo Wonder Dog Fighter, it calls for fine tuning to attain better steering response and improve grip when cornering so you don't slide off the side of the track. Minute changes can make huge advancements. Our easy to understand list will show you how and lead you to the optimum Set-up to put you in front of the rest on the track.

ebay









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Yokomo YZ-834B Wonder Dog Fighter ★
Yokomo YZ-834B Wonder Dog Fighter

★ Yokomo YZ-834B Wonder Dog Fighter Chassis ★
Yokomo YZ-834B Wonder Dog Fighter Chassis

★ Yokomo YZ-834B Wonder Dog Fighter Chassis ★
Yokomo YZ-834B Wonder Dog Fighter Chassis

★ Yokomo YZ-834B Wonder Dog Fighter Chassis ★
Yokomo YZ-834B Wonder Dog Fighter Chassis


Buying a Used Yokomo Wonder Dogfighter Buggy (and What to look for)


   Buying a used Yokomo Wonder Dogfighter Electric Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Yokomo website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

Dampers
   When you receive your used Yokomo Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Yokomo models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Yokomo Wonder Dogfighter is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Wonder Dogfighter model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Wonder Dogfighter Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Wonder Dogfighter steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Yokomo Wonder Dogfighter is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Yokomo Buggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Wonder Dogfighter model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Wings

   When you think of the Wing or the spoiler on any RC model car, you immediately think of down-force, but which wing is best for your model and what setting should it have?

   When you first build your car, most drivers will cut out the wing supplied in the kit, put it on the car and forget about it. It's only when the new kid at your local track, starts beating you that you begin thinking about changing a few things to make your car faster and one of the easiest changes you could make is to your wing.

   Choosing a wing for off-road can be confusing, so first of all you need to understand just what your wing can do for the way your car handles. Down-force equals traction and traction is what you need for controlled acceleration. The correct wing on your car can give you a good proportion of that down-force and if it has high side panels, it can also improve cornering and straight line stability.

   The first thing you need to consider when choosing your wing is the size. A small wing may not give as much down-force as a larger one, but it also weighs less and provides less speed restricting drag. So, if the track you will be racing on has good traction naturally and has nice long straights, a small wing may be an advantage. Large wings will obviously give you more down-force and on tracks with poor traction and short straights, will be the obvious choice. If rear end grip on cornering is also a problem, go for those high side panels as well.

   Tuning your wing angle can also improve the way it performs. A more acute angle will give you improved grip, but will also increase drag. If you go more flat with your wing, down-force is reduced, but drag is also reduced, so setting your wing angle is simply a matter of trial and error to suit your needs.

   The way the wing is mounted on your car must also be considered. If it uses a wire, it has a tendency to flex as it pushes down; this obviously flattens the angle as you speed along the straights, reducing drag, which could be good in some cases, but bad in others. If your wing is held by a rigid alloy or plastic support, the previous consideration is not a problem. Down-force is maintained as constant, but so is the drag.

   Changing and tuning things like your wing may seem futile if you are the big fish in a small pond and winning at your local track is not a problem. But if you ever go to the bigger ponds, its considering things like this that can keep you competitive.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Bearing Seals

   If you were to ask anyone with a modicum of experience in RC, they will tell you that the best modification you can make to a basic RC model, is to add a set of ball bearings.

   Quite a few of the entrance level models at the time this article was written, come with plastic and sintered brass bushings (ring type bearings). If these bearings are installed in the model and coated with grease as advised in the car manual, dust and grit can be caught in that grease and be dragged into the bearing where it can abrade the shaft that spins in it and it won't be long before it becomes a very sloppy fit, causing all kinds of problems.

   But what should you look for when buying bearings? There are a number of types of seal used on ball bearings and there is much debate concerning which is the best for RC.

   Rubber and Cork bearing shields are two of the more common types available, but although they are very effective when it comes to preventing dust and grit entering the bearing, they also create more drag in the bearing due them rubbing against the bearing to create friction. For this reason, if I wanted to race my model at any level and that model was fitted out with rubber or cork shielded bearings, I would change them ASAP.

   Steel and Teflon bearing shields may not be as effective as the rubber shielded versions, but they don't rub on the bearing, so little or no friction is created. The problem with this kind of bearing of course is that they need much more maintenance and are often more expensive.

   Basic shop bought bearings generally come packed with grease for their lubrication. However, if you want to have your bearings spin freely; grease is not the best thing to use. So, before you install your new bearings in your car, the first thing you need to do is clean out the grease with something like isopropanol and replace with thin oil.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: