RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Redcat Racing Monsoon XTR.
RCScrapyard Radio Controlled Models
Flags

1/8 Scale Nitro Truck/Truggy:

Redcat Racing Monsoon XTR (Radio Controlled Model Review)


Navigation: Sitemap  ▶  Manufacturers  ▶  Redcat Racing

History, Info (and How To Set-up Tips) for the Monsoon XTR:


  Introduced by Redcat Racing circa 2008, the 4WD Monsoon XTR Truggy, came with an SH28 engine, composite disk brakes and full radio system.

  The model is shaft driven, on an anodised alloy plate chassis, with 3 x gear type differentials, coil spring over oil filled dampers, dogbone drive-shafts and a full set of ball bearings.

Redcat Racing Monsoon-XTR
▼ Scroll Down for More Images ▼


  To race the Redcat Monsoon XTR, it must be fine tuned to improve handling, provide responsive steering and give you the grip to cruise around corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our step by step procedure, will guide you to the best Set-up for your individual driving style.

ebay









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Redcat Racing Monsoon XTR ★
Redcat Racing Monsoon XTR

★ Redcat Racing Monsoon XTR Chassis ★
Redcat Racing Monsoon XTR Chassis

★ Redcat Racing Monsoon XTR Chassis ★
Redcat Racing Monsoon XTR Chassis

★ Redcat Racing Monsoon XTR Chassis ★
Redcat Racing Monsoon XTR Chassis


Buying a Used Redcat Monsoon XTR Truggy (and What to look for)


   Buying a used Redcat Monsoon XTR Nitro Truggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Redcat website, or purchased separately on eBay. With an instruction manual, any problems with your model Truggy you may discover can easily be fixed.

Dampers
   When you receive your used Redcat Truggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Redcat models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Redcat Monsoon XTR is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Monsoon XTR model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Monsoon XTR Truggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Truggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Truggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Monsoon XTR steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Redcat Monsoon XTR is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Redcat Truggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Monsoon XTR model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Slipper Clutch and Hydra-Drive

   More often installed on off road RC Models, the Slipper Clutch has been around since the late 1990s. Basically the idea is to prevent wheel spin and increase traction under acceleration, to improve the cars stability from a standing start, when landing from jumps or on corner exits. It also protects the spur gear and drivetrain, to some degree, when using a high torque motor.

   The design is quite simple, employing two independent metal plates, one generally fixed to the spur gear and the other to the drive mechanism, clamping onto a fibre or rubber ring or pad. Adjustment is commonly achieved by slackening or tightening a spring loaded nut on the end of the spur gear mount.

   Setting up the slipper clutch can take some time and is a matter of individual preference, but normally the way to do this is from a standing start, jamming on the throttle and simply getting the feel of the car for that particular surface, being grass, gravel or dust. Personally I adjust it to give me around a metre and a half slip, before it achieves full drive. Wear on the slipper clutch is natural and often has to be readjusted after each race.

   The Hydra-Drive, or Fluid Coupling design has actually been around since the 1950s, but only came to RC a couple of years after the introduction of the slipper clutch. In principle, the Hydra-Drive is supposed to give similar results to the slipper clutch but need less continuous adjustment. In practice, for me anyway, it was not easy to live with.

   Hydra-Drives employ two independent impellers, immersed in silicone oil and enclosed in a sealed housing. Again, like the slipper clutch, one impeller is fixed to the spur gear, the other the drive. As power is applied, the spur gear will spin its impeller, until through the oil, drive is picked up by the drive impellor. The only real way to adjust the drive was to change the oil viscosity, or in some, the gap between the impellers could be adjusted by shims. All this took time and as far as I am aware, the Hydra-Drive is no longer used in RC.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Shock Mount Settings

   The combinations of Shock settings available on the majority of on and off road cars are far too many for this article to cover, so I will endeavour to explain some of the basics, that should give you some idea what these changes might achieve. Some of the settings suggested may not be available on all RC model cars.

   If you look at the lower wishbones of you model, you may see a number of holes alongside where the ball studs for the dampers are positioned. If you were to remove those studs on the rear wishbone and reposition them in the hole further out from the center of the car, the first thing you will notice is the ride height has dropped, this can be corrected by adding C spacers above the springs. The second thing you will notice is the shocks are more sluggish, this can be compensated by using thinner oil. If this adjustment is made on an off-road car, it can be advantageous for landing after big jumps, providing improved stability due to the increased hydraulic pack in the shocks (as described in my previous article). This setting can also improve the way cars handle small bumps and dips in the track, due to the softer static damping.

   Changing the mounting hole positions used by the dampers, on the wishbone or on the shock tower, will always change the angle the dampers lay. This angle is what changes the characteristics of the shocks in that they will react to different track types and conditions. The above example is just food for thought, for those looking to improve their cars handling in relation to any other settings, such as caster, camber, toe-in etc, they may have previously made on their car. The only way to really get to grips with this subject is through trial and error.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: