RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Megatech Nitro Razor-XT.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Nitro Rally/Touring Car:

Megatech Nitro Razor-XT (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Megatech

All Manufacturers: Model Types  >  On Road  >  1/10 Nitro On Road

History, Info (and How To Set-up Tips) for the Megatech Nitro Razor-XT:

  Introduced by Megatech circa 2000, the 4WD Nitro Razor XT Touring Car, was available RTR with an M-16 engine, radio system and three bodyshell options: # MTC 7802 Red Porche 911 - # MTC 7803 Lexus - # MTC 7804 Merc CLK.

  The model was shaft driven, on an alloy plate chassis, with gear type differentials, coil spring over oil filled dampers, anti roll bars, dogbone drive-shafts, 2-speed transmission and a full set of ball bearings.

Megatech Razor-XT
▼ Scroll Down for More Images ▼


  To race the Megatech Razor-XT, it requires time and patience, to tune and adjust for improvements in handling and steering ability and to get the grip you need to stay on course when manoeuvring around tight, slippery corners. A little can be a lot when it comes to changing your cars settings and our easy methodical directions will guide you to the best Set-up to help you win and keep you winning.

  Our easy to understand guide will show you how to adjust the Nitro Engine for your Razor-XT.

  Employing a number of sensible ideas, find out how you can avoid Radio interference, and problems with your Servo, by making a few changes to the layout of your equipment in your chassis. Discover what the top drivers do to improve the efficiency of their Megatech Razor-XT Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags


★ Megatech Nitro Razor-XT ★
Megatech Nitro Razor-XT

★ Megatech Nitro Razor-XT Chassis ★
Megatech Nitro Razor-XT Chassis

★ Megatech Nitro Razor-XT Chassis ★
Megatech Nitro Razor-XT Chassis

★ Megatech Nitro Razor-XT Chassis ★
Megatech Nitro Razor-XT Chassis

★ Megatech Nitro Razor-XT Chassis ★
Megatech Nitro Razor-XT Chassis

★ Megatech Nitro Razor-XT Chassis ★
Megatech Nitro Razor-XT Chassis


Buying a Used Megatech Razor-XT
Touring Car (and What to look for)


   Buying a used Megatech Razor-XT Nitro Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the road.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Megatech website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Megatech Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Megatech models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Megatech Razor-XT is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Razor-XT model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Razor-XT Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Razor-XT steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Megatech Razor-XT is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Megatech Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Razor-XT model and good racing.


For More on how to Setup your Touring Car, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Choosing a Transmitter

   When you first started in RC, you may have purchased a package that came with the car kit, motor, battery, charger, ESC and radio system complete. The transmitter was probably just a basic steer wheel, or stick type, with nothing more than forward, reverse, left, right and simple trim settings to centralise the servo and ESC.

   After a while, as your enthusiasm grows and your experience increases, you will want to move on to a better radio system, with more setting options, but where do you begin?

   Choosing the right transmitter is a personal thing. It has to feel right, have the balance you like, not be too bulky for your hand size and have all the features you might need to set up your car to your driving style.

   Transmitters these days are highly sophisticated pieces of engineering and once you choose you transmitter you will probably stick with it for the rest of your competitive career.

   Don't just go for the one you see in a review that looks and sounds like the best thing there could ever be and comes at a bargain price. Then when it arrives through the post and you get it in your hands it just doesn't have the feel you thought it would have. Sits awkwardly in your hands and is so complicated to set up you need a university degree to understand it.

   Talk to the experienced racers at your local track, ask them their opinion, see what their transmitter is like and if they will allow you to, hold it in your hands and see how it feels. All the best buys in life are made by recommendation. Then, once you have some idea what you are looking for, look on the internet for that model to get the best price, or go to a dealer and check out the latest models.

   Frequency choice depends on where in the world you live and what form of RC you are into. Fortunately, most of the top end transmitters can change to different frequency ranges by simply fitting a different module, so if you ever move up to an international level, you don't have to buy a new transmitter, just a module and receiver.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Ride Height

   To allow the suspension on any RC model to do its work properly it needs to settle in a position that is somewhere between it being able to react to any bumps and holes it may encounter on the track. To do this, it needs to be adjusted to somewhere in-between those limits. That position is termed the ride height and is generally measured with the car race ready, that means with the motor and battery etc installed and is the distance between the underside of the chassis and the ground.

   Simply speaking, determining ride height is dependent on the specific track conditions. For off road models the rule is simple, the bigger the bumps and the deeper the holes, the higher the ride height. On road, the closer the car is to the track, the better it will handle.

   For 1:10 Buggys I generally recommend a starting point for ride height at around 20mm. 1:10 Trucks and Truggys, 30mm upwards, depending on the wheel diameter. For On Road models, as low as possible, but normally the setting is around 5mm.

   Ride height doesn't just affect the way the car handles uneven track conditions, it also influences the way the car handles when cornering. For a stable car, body roll must be kept to a minimum and keeping the ride height low, is by far the best and easiest way to control it.

   Before you begin to set the ride height, it is best to make sure that each pair of shocks are exactly the same length, have the same spring type and same silicone oil weight. Also, if you don't have a ride height gauge of any kind, decide what height you want set your car to and prepare some kind of slip gauge to that dimension, a book, a pen, or anything that measures to what you want. I used an old square plastic servo mount, which was exactly 5mm for my touring car. It may be low tech, but it is just as accurate as any gauge you can buy.

   To set the ride height, the race ready car must be placed on a flat surface. Slide your slip gauge under the chassis and adjust the height by adding or removing tension to the damper springs. This is done on most models by using small C shaped clips, placed over the damper, above the springs, or on a number of top of the range models, this adjustment can be made by screwing a knurled nut on each threaded damper body. As a rule if the springs are compressed by more than 25% they should be replaced by stiffer springs. The gauge should just slide under the chassis on all four corners of the chassis.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: