RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Team Losi Ten SCT Nitro 1/10 Nitro Truck.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Nitro Truck/Truggy:

Team Losi Ten SCT Nitro - TLR0129 (Radio Controlled Model Review)


Navigation: Sitemap  ▶  Manufacturers  ▶  Team Losi

History, Info (and How To Set-up Tips) for the Losi Ten SCT Nitro:


  Released by Losi in 2012, the 4WD Ten SCT Nitro Short Course Truck RTR - TLR0129 - is shaft driven, on an anodised alloy plate chassis, gear type differentials, coil spring over oil filled dampers, anti roll bars, CV universal joint drive-shafts, a full set of ball bearings and came with a 3.4cc nitro engine and Spektrum 2.4Ghz radio system.

Team Losi Ten SCT Nitro
▼ Scroll Down for More Images ▼


  To race the Losi Ten SCT, it needs to be tuned to perfection for better stability, precise steering and provide enough grip to keep you on the track when going around tight bends at high speed. Even the smallest adjustment can change the feel of a car and our simple to follow instructions will guide you to the best Set-up to get you to the front and keep you there.

ebay









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Losi Ten SCT Nitro ★
Losi Ten SCT Nitro

★ Losi Ten SCT Nitro Chassis ★
Losi Ten SCT Nitro Chassis


Buying a Used Losi Ten SCT Nitro Truck (and What to look for)


   Buying a used Losi Ten SCT Nitro Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Losi website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

Dampers
   When you receive your used Losi Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Losi models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Losi Ten SCT is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Ten SCT model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Ten SCT Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Ten SCT steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Losi Ten SCT is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Losi Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Ten SCT model and good racing.




▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Tires for RC Models

Sponge (Foam) Tires:

   Sponge Tires can be purchased either pre mounted, glued and trued on the rims, or separately. Fitting the Tires onto the rims can be messy, so here are a few tips to make it a bit easier.
   If you are fitting new Tires on old rims, make sure the old sponge Tire is completely removed. To do this, I recommend using a wood lathe and apiece of wood, at least 300mm long and more than the width of your wheels, with medium grit emery paper stuck to it ... sand paper will also work, but emery is harder wearing ... This will also be used for truing a wheel. (Described later)

How to Mount and Glue Sponge Tires onto Wheels/Rims.

1/   Mount the Tires on the rims. Make sure they are reasonably tight on the rims, too loose and you might have problems.

2/   I find this to be easier if either in the lathe, or on the car itself. (but be careful with that glue)
  Using your thumb and forefinger, lift up the Tire off the rim, then using a small spatula or a thin piece of rigid wood or plastic dipped in glue (I recommend Evo-Stik, Impact Adhesive) slip it in the gap, making sure both the Tire and the rim are smeared. Then lower the Tire back onto the rim and press it down. Turn the Tire approximately 60 degrees and repeat.

3/   Depending on the width of the Tire you may need to repeat the process on the inside also.


How to True Sponge Tires.

   Truing Sponge Tires is essential if you are serious about racing competitively. To do this you will need the piece of wood, as described earlier and a good pair of vernier or digital calipers.
   Sponge Tires will always wear unevenly, weather you race on Carpet or Tarmac. The outside wheels will always end a race smaller than the ones on the inside, so after each race I recommend swapping them over (unless you are fortunate to have a new set for each race) and dont forget to adjust the steering trim on your transmitter before the next race.

1/   Before starting, check each mounted Tire for diameter and order them smallest to largest. Start with the smallest and mount it in the lathe.

2/   Make sure you are wearing safety glasses before you start this procedure: Lay the sanding wood under the Tire so that it can be pivoted up from behind onto the Tire. Start the lathe spinning, so that as you stand infront of the Tire, it is rotating downwards. Slowly lift the sanding wood and try to hold it ridged as it comes up against the Tire. There will be a high point on the Tire that if you hold the bat rigid enough will eventually wear down until the Tire appears completely concentric. at this point stop the lathe and measure the diameter on the inside and outside of the width. If needs be, repeat the process until satisfied.
Repeat for each Tire, matching them in pairs for diameter.
If considered necessary also trim the sides.


For More Setup Information check out my Hints and Tips page.







Hints and Tips

Your First Race Meeting

   When you finally find a racing club near to where you live, that initial experience of stepping up onto the rostrum and looking down over the track can be very daunting. But soon, as the race starts, adrenaline will kick in and away you go. For the next five minutes, your focus is on nothing but getting your car around each corner, avoiding all the other cars on the track and just getting to the end of the race.

   Maybe your batteries dumped or you crashed and the car was damaged, perhaps you didn't actually come last, whatever happened, it doesn't really matter you are well and truly hooked.

   When the race is over, don't be afraid to ask the more experienced racers questions about setup, driving tips etc. They have all been where you are now and will be more than willing to help you. Show them your car, get some tips on tires, gearing and general set-up for the club track.

   Then, when you get back home, go through all your races in your mind. Try to identify the things you did wrong and figure out how to avoid those mistakes next time. Think about what all the more experienced racers told you and change your settings as they advised.

   Put down a few buckets or cones in the back yard to practice driving round, something that if you hit it won't damage your car. Get someone to time you for say ten laps and each day after school, try to beat that time. The adage, "Practice makes perfect" holds true in many things, not least the sport of RC racing and as your confidence increases, your racing skills improve and the trophies begin to line up on your bedroom shelf, you will one day yourself be the guy all the newbie's look to for advice and you will remember that day, you nervously stepped up onto that platform for the first time, looked down across the track and how your whole life changed in that fleeting moment.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: