RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Kyosho Sandmaster.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Electric Buggy:

Kyosho Sandmaster - 30831 / 30832 (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Kyosho

All Manufacturers: Model Types  >  Buggys  >  1/10 Electric Buggys

History, Info (and How To Set-up Tips) for the Kyosho Sandmaster:


  Released by Kyosho in 2012, the entry level 2WD Sandmaster is available ReadySet - # 30831 - or as a Kit - # 30832. A Combo Kit was also available - # 30833.

  The model has a molded plastic chassis, with gear type differential, coil spring over oil filled dampers, dogbone drive-shafts and a full set of ball bearings.

Kyosho Sandmaster - 1:10 Electric RC Buggy
▼ Scroll Down for More Images ▼


  To race the Kyosho Sandmaster, you need to tweak and adjust all you can to give your car improved handling, stability and grip to ease around the curves and keep you on the track. One little setting change can transform your car into a world beater. Just follow our chart to attain the most favourable Set-up to suit your particular needs on any track.

  Learn what to look for when you search for the right Electric Motor for your Sandmaster and achieve the best Gearing, for the best performance and put you on the winners rostrum.

  See how the highest level racers optimise and halve the friction of their Bearings with some easy to implement tips. Discover what you can do to avert Radio interference, and the optimum conditions to Charge your Batteries, to help keep them in good condition and give you excellent performance.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Kyosho Sandmaster 2012 ★
Kyosho Sandmaster 2012

★ Kyosho Sandmaster 2012 Chassis ★
Kyosho Sandmaster 2012 Chassis

★ Kyosho Sandmaster 2012 Chassis ★
Kyosho Sandmaster - Chassis

★ Kyosho Sandmaster 2012 Chassis ★
Kyosho Sandmaster - Rear view Chassis


Buying a Used Kyosho Sandmaster Buggy (and What to look for)


   Buying a used Kyosho Sandmaster Electric Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Kyosho website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

Dampers
   When you receive your used Kyosho Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Kyosho models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Kyosho Sandmaster is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Sandmaster model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Sandmaster Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Sandmaster steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Kyosho Sandmaster is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Kyosho Buggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Sandmaster model and good racing.


For More on how to Setup your Buggy, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Getting into RC

   When I first got into racing RC, all I had was a three year old clapped out Tamiya Boomerang, a silver can stock motor, three step mechanical speed controller, two 1400Mah stick batteries and basic Acoms stick transmitter.

   I was the newbie and most of the guys I was racing against had all the latest models, modified motors, matched batteries and top spec radio equipment, but I was still beating them easily. Why? The answer is simple: Practice. I had been driving that old car around my back yard and in the local park for almost three years. The others bought their cars only a few weeks or months earlier and had pestered their parents for the latest and most expensive car, motor etc, but did not have the experience to be able to control it. While I was steadily trundling around the track, they were crashing out on every other corner, popping ball joints, breaking wishbones and generally causing havoc.

   The moral of this story is all too obvious and anyone starting up in RC who wants to race please take note. You don't need the best equipment to win races. You can start with a cheap basic kit and with a lot of practice in some wide open spaces where you will not cause any damage, learn how to control your car. Remember don't try to run before you can walk. Stick with that silver can motor for a while and upgrade to something a little faster only when you have mastered the old one. You don't even have to buy new. If you go down to your local RC Club, there are always cars for sale. They may be battered and bruised, but if you get an old brushed silver can motor, a cheap 5A ESC, a couple of Nicad, or Nimh batteries, charger and simple radio gear, that is all you need to start practising and after a while, winning races.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Soldering Battery Packs

   Nicad and Nimh batteries sometimes come as six separate matched 1.2 volt cells. These of course have to be soldered to each other in series to produce either a side by side stick pack, or a two times three cell saddle pack.

   Special copper, or silver plated straps must be used to make up these packs and each strap must be prepared before attempting to solder it to the battery cell, by placing a blob of solder at each end of all the straps needed.

   A jig to hold the cells vertical and side by side is advisable. Using electrical solder, with a flux core (flux aids the flow and adhesion of the solder) heat your soldering iron to as hot as it will go. Then with the stick of solder touching on the end of the cell, touch it with the iron. What you want it to spread evenly on the central part of the pole of the cell. Count to 3 seconds. If it doesn't melt the solder in that time, your iron is not hot enough. Battery cells are notoriously very fragile and susceptible to the very high temperatures soldering requires. Anything longer than four or five seconds direct contact with the iron can cause damage to the crystal structure in the cell, so be wary.

   When you have solder on each end of each cell, line them up in the jig, positive to negative and dab a spot of flux on the soldered cells, then position your straps, with the solder coated side faced down, touching the solder on the end of the cell. Now place your hot iron on the strap. Heat will transfer through the strap and melt the solder on the two faces. Again, count to 3 and you should feel the strap drop slightly as the solder fuses with the solder on the cell. Repeat this for each cell on both sides to produce your desired configuration. Finally solder your two wires, previously prepared with connectors, to the pack. Do not solder wires with bare ends to your pack. If these wires were to touch and short out, you could effectively kill your expensive battery pack I use Red for positive and Black for negative, but so long as you know which is which electrical equipment does not like the battery to be connected the wrong way.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: