RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Kyosho Circuit 20, Toyota Hilux
RCScrapyard Radio Controlled Models
Flags

1/8 Scale Nitro Truck/Truggy:

Kyosho Circuit 20, Toyota Hilux - # 3027 (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Kyosho

All Manufacturers: Model Types  >  Trucks/Truggys  >  1/8 Nitro Trucks/Truggys

History + Information (and How To Set-up Tips):


  Released by Kyosho circa 1983, the 2WD Circuit 20, Toyota Hilux Truck - # 3027 - was based on an alloy ladder-frame, with plastic tub chassis and came with a factory assembled gearbox, un-damped coil spring suspension (oil filled damper option was available) and dogbone drive-shafts. An engine for the kit had to be purchased separately.

Kyosho Circuit 20, Toyota Hilux
▼ Scroll Down for More Images ▼


  To race the Kyosho Toyota Hilux, it requires time and patience, to tune and adjust for improvements in handling and steering ability and to get the grip you need to stay on course when manoeuvring around tight, slippery corners. A little can be a lot when it comes to changing your cars settings and our easy methodical directions will guide you to the best Set-up to help you win and keep you winning.

  Our easy to understand guide will show you how to adjust the Nitro Engine for your Toyota Hilux.

  Employing a number of sensible ideas, find out how you can avoid Radio interference, and problems with your Servo, by making a few changes to the layout of your equipment in your chassis. Discover what the top drivers do to improve the efficiency of their Kyosho Toyota Hilux Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Kyosho Circuit 20 Toyota Hilux ★
Kyosho Circuit 20 Toyota Hilux

★ Kyosho Circuit 20 Rally Chassis ★
Kyosho Circuit 20 Rally Chassis

★ Kyosho Circuit 20 ★
Kyosho Circuit 20 Gearbox


Buying a Used Kyosho Toyota Hilux
Truck (and What to look for)


   Buying a used Kyosho Toyota Hilux Nitro Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Kyosho website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

Dampers
   When you receive your used Kyosho Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Kyosho models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Kyosho Toyota Hilux is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Toyota Hilux model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Toyota Hilux Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Toyota Hilux steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Kyosho Toyota Hilux is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Kyosho Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Toyota Hilux model and good racing.


For More on how to Setup your Truck, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Tires for Off-Road RC Models


   If you only ever intend to race your Buggy, Truggy or Truck at your local track each week end, you will soon learn the best tire - insert combination for your particular model on that specific track surface type. But if you ever visit other tracks in your area, or move on to the national or international race meetings, at other tracks throughout the country, you will soon discover that your trusty setup will not work as well and you will be forced to invest in many more sets of wheels and tires.

   The choice of Off-Road tires available is mind boggling and the combinations of Mini-Pin, Micro-Pin, Block, Stud and Ribbed Tires, with all the various types of foam inserts available is a mine field, even for the more experienced.

   Local knowledge is always the place to start and the second visit made to any particular track is always better than the first, provided you keep good records of your tires, inserts and general set-up for each race.

Tires and Inserts for Jumps


   Most tracks for off-road RC models - indoor or outdoor, have at least one jump for you to negotiate and on a high number of tracks, it is how you land from that jump that will determine where you finish in the race.

   Setting the droop and adjusting the damper oil or coil spring tensions will go a long way to ensuring you land from the jump on all four wheels and keep control of your car as you exit the jump, but the correct choice of tire insert can also have an effect on how much grip you have when you land and accelerate to the next corner.

   As a rule of thumb, the higher the jump, the harder the foam insert needs to be. If the jump is long and not too high, a softer foam insert may give improved grip.

   Once you have determined the best tire combination and before you glue the tires to the rims, trial and error with different inserts on your practice laps before racing, can reap huge benefits.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Shock Mount Settings

   The combinations of Shock settings available on the majority of on and off road cars are far too many for this article to cover, so I will endeavour to explain some of the basics, that should give you some idea what these changes might achieve. Some of the settings suggested may not be available on all RC model cars.

   If you look at the lower wishbones of you model, you may see a number of holes alongside where the ball studs for the dampers are positioned. If you were to remove those studs on the rear wishbone and reposition them in the hole further out from the center of the car, the first thing you will notice is the ride height has dropped, this can be corrected by adding C spacers above the springs. The second thing you will notice is the shocks are more sluggish, this can be compensated by using thinner oil. If this adjustment is made on an off-road car, it can be advantageous for landing after big jumps, providing improved stability due to the increased hydraulic pack in the shocks (as described in my previous article). This setting can also improve the way cars handle small bumps and dips in the track, due to the softer static damping.

   Changing the mounting hole positions used by the dampers, on the wishbone or on the shock tower, will always change the angle the dampers lay. This angle is what changes the characteristics of the shocks in that they will react to different track types and conditions. The above example is just food for thought, for those looking to improve their cars handling in relation to any other settings, such as caster, camber, toe-in etc, they may have previously made on their car. The only way to really get to grips with this subject is through trial and error.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: