RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► HPI Maverick Blackout ST.
RCScrapyard Radio Controlled Models
Flags

1/5 Scale Nitro Truck/Truggy:

HPI Maverick Blackout ST - # MV12403 (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  HPI

All Manufacturers: Model Types  >  Trucks/Truggys  >  1/5 Nitro Trucks/Truggys

History, Info (and How To Set-up Tips) for the HPI Maverick Blackout ST:


  Distributed by HPI Racing circa 2011, the 4WD Maverick Blackout ST Stadium Truck - # MV12403 - came RTR with a 30cc engine and 2.4Ghz radio system.

  The model is shaft driven, on an alloy plate chassis, with gear type differentials, coil spring over oil filled dampers, dogbone drive-shafts and a full set of ball bearings.

HPI Maverick Blackout ST - 1:5 Nitro Truck
▼ Scroll Down for More Images ▼


  To race the HPI Maverick Blackout ST, it needs to be tuned to perfection for better stability, precise steering and provide enough grip to keep you on the track when going around tight bends at high speed. Even the smallest adjustment can change the feel of a car and our simple to follow instructions will guide you to the best Set-up to get you to the front and keep you there.

  Our basic instructions will help you set-up and fine tune the Nitro Engine for your Maverick Blackout ST.

  With a few simple tips, we will show you how to easily avert Radio interference, and Servo problems, by simply repositioning the receiver or using some of the latest developments. Learn how to combat friction and get more from your HPI Maverick Blackout ST Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ HPI Racing Maverick Blackout ST Chassis ★
HPI Racing Maverick Blackout ST Chassis

★ HPI Racing Maverick Blackout ST Chassis ★
HPI Racing Maverick Blackout ST Chassis


Buying a Used HPI Maverick Blackout ST Truck (and What to look for)


   Buying a used HPI Maverick Blackout ST Nitro Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the HPI website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

Dampers
   When you receive your used HPI Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those HPI models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your HPI Maverick Blackout ST is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Maverick Blackout ST model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Maverick Blackout ST Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Maverick Blackout ST steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your HPI Maverick Blackout ST is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used HPI Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Maverick Blackout ST model and good racing.


For More on how to Setup your Truck, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Emergency Plastic Part Repairs

   It always happens when you least expect it. You are racing hard; and suddenly some idiot decides to side swipe you' and break your front wishbone. Even though you may carry spare parts for just about everything on your car, it always seems to be the same part that breaks and although you made a mental note the last time it happened to get a replacement you soon realise those mental notes were not worth the paper they are written on.

   So there you are, in the middle of nowhere with no spares. You ask around and no one has anything like your car, least of all parts for it and the closest model shop is 100 miles away. What are you supposed to do now?

   Some kind of repair is your only option.

   The one thing quite a few people think of first is superglue, but that kind of repair won't even get you around the first corner.

   What you need is something much stronger and the only way you can do that requires a good quality soldering iron, the plastic sprue (the bit left over when you remove all the parts for your car) or another broken part made from the same plastic.

   Using the largest tip you have, set the temperature so that it melts the plastic, but does not vaporise it. Place your broken part on a flat surface that will not be affected by the heat from the iron. I use the glass plate I have for setting the wheel camber of my model. Next, cut a piece of scrap plastic long enough for you to be able to hold on one end, as you work with it and place it over the break. At the point directly over the break, carefully melt the scrap plastic until it is around one millimetre above the break.

   Gently slide the iron sideways, depositing the scrap plastic about five millimetres either side and around the break. At each end of the fix, try to meld the scrap and broken part plastic. Picking up the broken part, continue the melding around each side of the break, then place it down the flat surface and repeat the process on the other side.

   When satisfied, switch off the iron and allow the plastic to cool. Using a modelling knife, carefully, cut away any excess plastic, but not too much.

   With a little practice a fix like this can be almost as strong as a new part and can save you a whole lot of anguish.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Aerodynamics

   It is commonly understood that weight improves traction. If you have ever seen TV coverage of any kind of full size motor racing, you will have heard the terms, aerodynamics and down force. Well, they also relate to small scale models in exactly the same manner.

   Bodyshell aerodynamics for RC model cars is a science in itself and the wrong one could loose you the race. Back in my day the shell to have for 1:10 on-road, was the Alfa Romeo 156. The bodyshell that came with the car kit was a Peugeot 406, but that soon went into the bin when I got the Alfa. The difference in performance was amazing, but it wasn't a patch on the Frewer, Ferrari F50. The rear wing on that bodyshell was phenomenal; it was the fastest thing on the track, great for club racing, but to my cost, illegal for top level racing. Regulations stipulate that the rear wing should be no higher than the roof of the car, the Frewer wing was way too high, so another one was relegated to the "do not use" box.

   Off-Road models also benefit from aerodynamics and down force, but to a lesser degree than on-road models. The rear wing provides good down force for improved traction on dirt tracks and is discussed in detail in one of my other articles.

   Way back in 1994, a company named Tenth Technology produced a 1:10 buggy called the Predator. The design of the car was innovative to say the least, with inboard laydown cantilever operated shocks and extra low, almost flat bodyshell. The most eye-catching element of the design was the wings. Not only did it have a nice large wing on the rear, it also had one of a similar size at the front. It was one of those cars where the idea seemed good and the car was fast very fast and did once win the British Championship. The problem was its fragility. Any small knock damaging the front wing, made it un-drivable.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: