RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Hot Bodies (HB) Lightning Stadium 10.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Nitro Truck/Truggy:

HB Lightning Stadium 10 (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Hot Bodies

All Manufacturers: Model Types  >  Trucks/Truggys  >  1/10 Nitro Trucks/Truggys

History, Info (and How To Set-up Tips) for the HB Lightning Stadium 10:


  Introduced by Hot Bodies circa 2006, the 4WD Lightning Stadium 10 Truck - # HB 66501 / 66502 / 66503 - came RTR with a 15 engine and radio system.

  The model was shaft driven, on an alloy plate chassis, with gear type differentials, coil spring over oil filled dampers, dogbone drive-shafts and a full set of ball bearings.

Hot Bodies Lightning Stadium 10 - 1:10 Nitro Truck
▼ Scroll Down for More Images ▼


  To race the HB Lightning Stadium 10, it needs to be tuned to perfection for better stability, precise steering and provide enough grip to keep you on the track when going around tight bends at high speed. Even the smallest adjustment can change the feel of a car and our simple to follow instructions will guide you to the best Set-up to get you to the front and keep you there.

  Our basic instructions will help you set-up and fine tune the Nitro Engine for your Lightning Stadium 10.

  With a few simple tips, we will show you how to easily avert Radio interference, and Servo problems, by simply repositioning the receiver or using some of the latest developments. Learn how to combat friction and get more from your HB Lightning Stadium 10 Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ HB Lightning Stadium 10 ★
HB Lightning Stadium 10

★ HB Lightning Stadium 10 Chassis ★
HB Lightning Stadium 10 Chassis

★ HB Lightning Stadium 10 Chassis ★
HB Lightning Stadium 10 Chassis

★ HB Lightning Stadium 10 Chassis ★
HB Lightning Stadium 10 Chassis

★ HB Lightning Stadium 10 Chassis ★
HB Lightning Stadium 10 Chassis


Buying a Used HB Lightning Stadium 10 Truggy (and What to look for)


   Buying a used HB Lightning Stadium 10 Nitro Truggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the HB website, or purchased separately on eBay. With an instruction manual, any problems with your model Truggy you may discover can easily be fixed.

Dampers
   When you receive your used HB Truggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those HB models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your HB Lightning Stadium 10 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Lightning Stadium 10 model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Lightning Stadium 10 Truggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Truggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Truggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Lightning Stadium 10 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your HB Lightning Stadium 10 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used HB Truggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Lightning Stadium 10 model and good racing.


For More on how to Setup your Truggy, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Bumpsteer

   In plain language, Bumpsteer is exactly what it sounds like. If your car goes over a bump, it will affect the toe-in setting and can on some tracks make handling of the car in a straight line difficult.

   To check if your car might have any problems with bumpsteer, have it in race mode, with the motor and battery etc in position. Place the car on a flat surface and push down your car at the front. Looking down from above, keep a close eye on the wheels and watch for any angular movement to the side. If there is then you have bumpsteer.

   For off road cars, because of them having longer dampers in comparison to on road, a small amount of toe out is considered by many as acceptable in the lower position and can sometimes be used as a tuning option because of its aggressive effect on turning ability when entering corners. On road cars, because of the shorter damper movement and the greater need for precise steering and stability in a straight line, generally have less of a problem. However if bumpsteer is detected, drivers generally try to eliminate this as much as possible.

   The standard settings for most kits from all manufacturers are adjusted to reduce bumpsteer as much as they can and it is only when you come to make changes to those settings yourself, to suit your personal driving style that bumpsteer can become a problem.

   Any changes you might make to the steering links or the caster could induce some bumpsteer, so you should check for it each time you make any adjustments in these areas.

   To adjust bumpsteer try adding or removing washers under each steering link outer ball stud. More washers will increase and fewer washers reduce bumpsteer.

   Steering geometry can be tricky to setup for those new to the sport and even some more experienced racers can struggle with this problem. So, unless you are having major problems with your cars handling, try to avoid making any radical changes and if you do, remember to only make one change at a time and make a note of it for future reference, incase you need to remove it.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Wheel Balancing

   At the tender age of 17 I passed my driving test. Of course, the first thing I did was to dash over to my girlfriends house and take her out to a long straight stretch of road close by where the boy racers would often congregate. No one was around that day, so the road was relatively quiet. I slowly went through the gears and we reached 65 with no problems, but as we got closer to 70, my hands sensed a small vibration on the steering wheel. By the time we reached 75, the steering wheel and the whole car was vibrating hard. I remember my girlfriend screaming for me to "slow down," Which I did of course and tried to laugh it off.

   Back home I told my dad what had happened and he reminded me, that just the week before we had put on a new set of front tires and it must be the balance that is out. Sure enough, after the wheels were balanced, 85, 90, was not a problem, the car drove perfectly.

   So, when I got deeper into RC, that memory returned and now I balance all my wheels.

   These days, wheel balancing equipment for RC cars is available from most RC model shops, but back then I had to make my own using the rear end of an old Tamiya F1 car. Here's how I did it.

   With the tire and insert mounted and glued, the wheel was fitted onto my home made balancer and allowed to settle. I would then gently turn the wheel through 90 degrees and again allow it to settle. Obviously the heavy side of the wheel would drop to the bottom due to gravity. Once I was satisfied, I would then make a mark on the rim with a felt tip pen at the top of the wheel where it came to rest. Removing the wheel I would mix a small amount of plastic resin and press a tiny amount of this into a recess on the wheel on the side where I made the mark. The whole process was then repeated until I was totally satisfied.

   I was amazed just how out of balance some of those wheels were and how much a small thing like that can make a difference on the track.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: