RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Hong-Nor X2-CRB-Pro.
RCScrapyard Radio Controlled Models
Flags

1/8 Scale Nitro Buggy:

Hong Nor X2-CRB Pro (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Hong Nor

All Manufacturers: Model Types  >  Buggys  >  1/8 Nitro Buggys

History, Info (and How To Set-up Tips) for the X2-CRB Pro:


  Developed by Jammin Products and manufactured by Hong Nor in 2008, the 4WD X2 CRB Pro Special Buggy, was shaft driven, on an alloy plate chassis, with 3 x gear type differentials, coil spring over oil filled dampers, anti roll bars, all round CVD universal joint drive-shafts and a full set of ball bearings.

Hong-Nor X2-CRB-Pro
▼ Scroll Down for More Images ▼


  To race the Hong Nor X2-CRB Pro, it requires time and patience, to tune and adjust for improvements in handling and steering ability and to get the grip you need to stay on course when manoeuvring around tight, slippery corners. A little can be a lot when it comes to changing your cars settings and our easy methodical directions will guide you to the best Set-up to help you win and keep you winning.

  Our easy to understand guide will show you how to adjust the Nitro Engine for your X2-CRB Pro.

  Employing a number of sensible ideas, find out how you can avoid Radio interference, and problems with your Servo, by making a few changes to the layout of your equipment in your chassis. Discover what the top drivers do to improve the efficiency of their Hong Nor X2-CRB Pro Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Hong Nor X2-CRB Pro Buggy Chassis ★
Hong Nor X2-CRB Pro Buggy Chassis


Buying a Used Hong Nor X2-CRB Pro Buggy (and What to look for)


   Buying a used Hong Nor X2-CRB Pro Nitro Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Hong Nor website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

Dampers
   When you receive your used Hong Nor Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Hong Nor models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Hong Nor X2-CRB Pro is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your X2-CRB Pro model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your X2-CRB Pro Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The X2-CRB Pro steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Hong Nor X2-CRB Pro is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Hong Nor Buggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your X2-CRB Pro model and good racing.


For More on how to Setup your Buggy, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Wheels

   When it comes to wheels, the majority of people tend to go for what looks good, something that will make their car stand out from the crowd, but are they the best wheels for you when it comes to winning races on the track?

   Quite a number of years ago I read an article in an RC magazine about RC model wheels and how important it is to have the right ones on your car. I was so impressed by that article that I immediately sold off all my old wheels and bought a batch of new ones why? Read on.

   In order for a tire to maintain grip, it needs to preserve the downward pressure through the cars suspension onto the road surface. To do this, not only must the wheels be concentric, they have to be totally rigid. So, if you accept that premise as fact, you will realise that the majority of the flashy wheel designs available for all types of RC model cars are not exactly what you might call rigid. In point of fact, they are down right flimsy.

   If you take a good hard look at some of those multi spoked pressure injected plastic wheels you have in your car box, you will soon see what I mean. Just take one in your hand, squeeze it just a little and you will realise how weak and feeble the construction of these cheap and nasty things are. Looks aren't everything. If you want to be up there with the best you have to strive for the best and that doesn't necessarily mean the most expensive. There are lots of wheels out there at reasonable prices that can give you that rigidity you need, okay, they might not look pretty, but they will perform better and give you that extra one percent that could mean the difference between winning and losing. You have to ask yourself, what you want your car to be, the one that everyone admires for its flashy good looks, or the one that gets you to the top.

   So there you have it, rigid wheels are the thing to go for. They may be heavier and provide a more dynamic rotating mass, requiring more braking than those flimsy lightweight wheels out there but then, that is a whole new subject.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Toe Angle

   When you first build your RC model car, you will no doubt have made all the settings advised in the manufacturers' manual and will take it out on the back yard not thinking of things like camber, caster or toe-in I know I did. It's only when you get competitive that you start learning about these things and just what a big difference they can make to the handling of your car. One of the more effective of these adjustments is Toe-in.

   The term, toe-in, toe-out, or toe-angle, refers to the alignment of the front or rear wheels, when viewed from above and is easily adjusted via the track rods or turnbuckles that link to the steering mechanism or directly to the steering servo horn.

   Front toe-in reduces steering when entering a corner, but improves steering response on corner exit under acceleration. On the straights, toe-in will also improve the cars stability while accelerating.

   Front toe-out will improve steering on corner entry, but makes the car unstable under acceleration on the straights and on bumpy tracks. The usual recommendation is to have up to 1 degree of either toe-in or toe out.

   Rear toe-in is generally found as the standard setting on most on-road and off-road RC models.

   More rear toe-in provides the car with more power under-steer, as well as improved stability and rear end traction. This setting is recommended for low grip tracks.

   Less rear toe-in slightly reduces steering on corner entry, but improved steering under acceleration.

   To measure toe-angle, I used to use my trusty vernier callipers to measure the width at the front of the wheels and the rear of the wheels and using this information along with the diameter of the wheels simply calculate the angle. Or, you could alternatively use this data to draw a triangle on a sheet of paper and measure the angle with your trusty school protractor.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: