RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Hobao Hyper GTBe.
RCScrapyard Radio Controlled Models
Flags

1/8 Scale Electric Rally/Touring Car:

Hobao Hyper GTBe (Radio Controlled Model Review)


Navigation: Sitemap  ▶  Manufacturers  ▶  Hobao

History, Info (and How To Set-up Tips) for the Hyper GTBe:


  Manufactured by Hobao in 2013, the 4WD Hyper GTBe Electric Touring Car, was based on the Hyper SS chassis series and is shaft driven, on an alloy plate chassis, with gear type differentials, coil spring over oil filled dampers, anti roll bars, rear dogbones, with front CVD universal joint drive-shafts and a full set of ball bearings.

  The model was marketed in the USA by Ofna Racing as the "Hyper GTe".

Hobao GTB-e - 1:8 Electric Touring Car
▼ Scroll Down for More Images ▼


  To race the Hobao GTB-e, you need to tweak and adjust all you can to give your car improved handling, stability and grip to ease around the curves and keep you on the track. One little setting change can transform your car into a world beater. Just follow our chart to attain the most favourable Set-up to suit your particular needs on any track.

ebay









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Hobao Hyper GTBe Chassis ★
Hobao Hyper GTBe Chassis

★ Hobao Hyper GTBe Chassis ★
Hobao Hyper GTBe Chassis

★ Hobao Hyper GTBe Chassis ★
Hobao Hyper GTBe Chassis


Buying a Used Hobao GTB-e
Touring Car (and What to look for)


   Buying a used Hobao GTB-e Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the road.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Hobao website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Hobao Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Hobao models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Hobao GTB-e is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your GTB-e model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your GTB-e Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The GTB-e steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Hobao GTB-e is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Hobao Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your GTB-e model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.





















★ Hobao GTB-e Chassis ★
Hobao GTB-e Chassis - 1:8 Electric Touring Car


Hints and Tips

Decals

   After spending lots of time and effort to paint your bodyshell, you come to the point where you make it look good by putting on all those flashy decals, but before you rush in with the scissors and start cutting, there are a few things you should do first.

   Good preparation is key to a perfect job, so before you do anything with your decals, you must first of all wash your hands and then make sure the bodyshell is clean and no oil or grime from your previously grubby fingers remains on the Polycarbonate Lexan surface. Methylated spirits is the thing to use, or failing that, use one of those wipes you use for your computer monitor screen. As the body shell dries, you can carefully cut out the decals from the sheet. Do the big ones first and leave the smallest ones for last.

   Now you can prepare to the decals for positioning. Carefully remove the backing paper from the decal with your thumb nail and then put it back on again, but slightly out of line. Place the decal in the position you want it on the bodyshell and when you are satisfied, press down the sticky corner onto the bodyshell and peel off the backing paper, following it along with your fingers to avoid any bubbles. Repeat the process until all your decals are in place.

   Any bubbles or misfitting areas can be corrected by using a sharp modelling knife to carefully pierce the bubbles, or score the poorly fitting area and complete the process with your finger nail.

   Some misalignments can often be fixed using a hair dryer on the offending decal to soften the glue enough to allow you to reposition it, but be careful; Lexan can react like heat-shrink and may wrinkle if you use too much heat.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Toe Angle

   When you first build your RC model car, you will no doubt have made all the settings advised in the manufacturers' manual and will take it out on the back yard not thinking of things like camber, caster or toe-in I know I did. It's only when you get competitive that you start learning about these things and just what a big difference they can make to the handling of your car. One of the more effective of these adjustments is Toe-in.

   The term, toe-in, toe-out, or toe-angle, refers to the alignment of the front or rear wheels, when viewed from above and is easily adjusted via the track rods or turnbuckles that link to the steering mechanism or directly to the steering servo horn.

   Front toe-in reduces steering when entering a corner, but improves steering response on corner exit under acceleration. On the straights, toe-in will also improve the cars stability while accelerating.

   Front toe-out will improve steering on corner entry, but makes the car unstable under acceleration on the straights and on bumpy tracks. The usual recommendation is to have up to 1 degree of either toe-in or toe out.

   Rear toe-in is generally found as the standard setting on most on-road and off-road RC models.

   More rear toe-in provides the car with more power under-steer, as well as improved stability and rear end traction. This setting is recommended for low grip tracks.

   Less rear toe-in slightly reduces steering on corner entry, but improved steering under acceleration.

   To measure toe-angle, I used to use my trusty vernier callipers to measure the width at the front of the wheels and the rear of the wheels and using this information along with the diameter of the wheels simply calculate the angle. Or, you could alternatively use this data to draw a triangle on a sheet of paper and measure the angle with your trusty school protractor.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: