RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Duratrax Maximum ST.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Nitro Truck/Truggy:

Duratrax Maximum ST - DTXC0055 / DTXD60** (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Duratrax

All Manufacturers: Model Types  >  Trucks/Truggys  >  1/10 Nitro Trucks/Truggys

History, Info (and How To Set-up Tips) for the Maximum ST:


  Introduced by Duratrax in 1998, the 2WD Maximum ST Stadium Truck, was available Pre-Built - DTXC0055 - without a radio system, or RTR - DTXD60** - with a Torq .12 engine and Hitec Lynx AM radio system.

  The model was based on an alloy plate chassis, with a gear type differential, coil spring over oil filled dampers, slipper clutch, dogbone drive-shafts and a full set of ball bearings.

Duratrax Maximum-ST
▼ Scroll Down for More Images ▼


  To race the Duratrax Maximum ST, it needs to be tuned to perfection for better stability, precise steering and provide enough grip to keep you on the track when going around tight bends at high speed. Even the smallest adjustment can change the feel of a car and our simple to follow instructions will guide you to the best Set-up to get you to the front and keep you there.

  Our basic instructions will help you set-up and fine tune the Nitro Engine for your Maximum ST.

  With a few simple tips, we will show you how to easily avert Radio interference, and Servo problems, by simply repositioning the receiver or using some of the latest developments. Learn how to combat friction and get more from your Duratrax Maximum ST Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Duratrax Maximum ST ★
Duratrax Maximum ST

★ Duratrax Maximum ST ★
Duratrax Maximum ST

★ Duratrax Maximum ST Chassis ★
Duratrax Maximum ST Chassis


Buying a Used Duratrax Maximum ST Truck (and What to look for)


   Buying a used Duratrax Maximum ST Nitro Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Duratrax website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

Dampers
   When you receive your used Duratrax Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Duratrax models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Duratrax Maximum ST is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Maximum ST model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Maximum ST Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Maximum ST steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Duratrax Maximum ST is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Duratrax Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Maximum ST model and good racing.


For More on how to Setup your Truck, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Tire Compounds

   Way back in the early 1990s when I first got into RC, most of the off-road models available came with chunky hard compound block tires that gave little or no grip on grass or dirt tracks. On-road didn't have this problem as they were still using sponge tires that with a coating of wintergreen based tire additive before each race to improve grip. There was even one guy who swore, before every race, he dipped his wheels in a glass of light ale.

   Then things started to change. By the mid 1990s tire manufacturers such as Losi and Schumacher began developing smaller pin tires, in softer compounds. These mini pin versions were a revelation for grass racers, but were only a small improvement on dust tracks.

   As new compounds were released, grip slowly improved. Then, with the release of the micro pin, super soft compound tires, off road was a completely different sport. Grip roll was now one of the problems drivers had to learn to contend with. This was something unheard of only a few short years before.

   Rubber Tires for On-road RC models had been around for a while in the early 1990s, but because sponge was so widely used, rubber never really caught on. Then, as Tamiya released its 1:10 on road models based on the off-road Manta Ray chassis, other manufacturers caught on and began producing their own 1:10 on-road cars. Schumacher released the SST 98, using the same gearbox and differentials as their Cat 2000 to reduce tooling costs. Tires were now being produced for this new scale in rubber. Pit Shimizu and Take-off were two of the leading RC on-road tire developers at the time, each releasing three different compounds, with recommended track temperature use. From that point on, on-road RC racing never looked back and the days of sponge and light ale came to a shuddering stop.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Look after your Gears

   In RC there are a number of different gear teeth sizes we tend to use, based on two systems. Imperial and metric. The imperial system has sizes 24dp, 32dp, 48dp and 64dp. DP stands for Diametral Pitch and the number refers to the number of teeth per inch. The metric system has sizes 0.4m, 0.5m, 0.6m, 0.7m, 0.8m and 1m. M stands for Module and is the ratio of the reference diameter of the gear divided by the number of teeth.

   The different sizes are used basically for strength. 32dp gears larger than 64dp gears, therefore it stands to reason that the 32dp gears are by design stronger and for this reason are more commonly used on a number of entry level buggys and nitro models because of the higher torque levels involved. Also, the bigger the scale of the model, the stronger the teeth need to be.

   64dp and its metric equivalents are generally the choice of 1:10 electric on-road racers, because of its higher range of ratio options and smoother action in comparison to other sizes. On-road models are not as hard on the gears as off-road, so the weaker, small tooth size is not a problem.

   48dp and its metric equivalents tend to be preferred by 1:10 off-road racers, mainly because of their strength in comparison to the 64dp and smoother operation than 32dp. Off-road models need gears that can handle all the knocks and bangs, as well as heavy landings off high jumps.

   Setting your gears is the most important part of looking after your gears.

   Backlash is basically the gap between the teeth in mesh. The perfect gear setting must have a small amount of backlash. To achieve the best setting use a very thin sheet of plastic between the pinion and spur gear teeth as you press them into mesh. After tightening the motor mount screws, use your fingers to spin the spur gear and roll out the plastic sheet. If the setting is correct, there will be a small amount of movement (backlash) between the gear teeth before they catch. If the mesh is too deep, there will be no movement between the teeth, this will create friction and if you run them like this, they will grind together, wear and break. If the mesh is not deep enough and only the tips of the teeth are touching, the excessive backlash will soon damage and strip the tops off the teeth rendering the gears useless.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: