RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Corally SP12G Pan Car.
RCScrapyard Radio Controlled Models
Flags

1/12 Scale Electric Pan Car:

Corally SP12G (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Corally

All Manufacturers: Model Types  >  On Road  >  1/12 Electric Pan Cars

History, Info (and How To Set-up Tips) for the SP12G:


  Introduced by Team Corally in 1991, the SP12 G pan car, came with a new Coral anti-roll trailing front beam with coil springs and dampers.

  For the SP12G, Corally replaced the Colal chassis, used for previous versions, with a new lightweight Graphite chassis, employing a free floating Coral T-bar, enclosed silicone damper, alloy rear pod, coil spring front suspension mounted inboard, strut linked front A arms, a smooth action ball-type differential and full set of ball bearings.

Corally SP12G
▼ Scroll Down for More Images ▼


  To race the Corally SP12G, it calls for fine tuning to attain better steering response and improve grip when cornering so you don't slide off the side of the track. Minute changes can make huge advancements. Our easy to understand list will show you how and lead you to the optimum Set-up to put you in front of the rest on the track.

  We give you all the basic information you need to guide you to the best Electric Motor for your SP12G and achieve the best Gearing, to get you in front on the track and keep you there.

  Find out how the worlds top professional RC racers get improved efficiency from their Bearings employing a number of sensible ideas. Find the way to avoid Radio interference, and basic instruction on how to Charge your Batteries, so they will last longer and provide improved power.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Corally SP12G ★
Corally SP12G

★ Corally SP12G Chassis ★
Corally SP12G Chassis

★ Corally SP12G Chassis ★
Corally SP12G Chassis


General Information and Advice

   For those starting in Radio Controlled Racing, here are a few Hints and Tips: Firstly, buy a Kit not an RTR. That way, if something breaks you will have some idea how to fix it.

   Radio Controlled Model Cars are very fragile and easily broken. The main parts to protect are the Front Wishbones, Suspension Shock Towers, Dampers, Hub Carriers, Kingpins, Uprights and Toe in Blocks, so make sure you have a good strong front bumper and Lexan or Hard Plastic Body Shell and if available for your model, a protective under tray, to prevent grit and dust getting into any moving parts.

   The Steering Servo is also a weakness in high speed crash situations, so get yourself some good strong Servo Mount and Servo Saver. Also I would recommend Titanium Shafts, Turnbuckles, Tie Rods and pivot/steering shafts and if available for your model, lightweight Titanium Drive shafts, dog bones and CVD (Constant Velocity Drives). The standard steel types are far too easily bent.

   Gearing is another problem area on RC model cars. Head on collisions can easily break off gear teeth on Nylon/Plastic Spur Gears and even Bevel Gears inside the Gearbox. Heavy impacts can also loosen nuts and self taping screws that hold the Motor in Position, allowing the Pinion Gear to pull out of mesh slightly and rip the tops of the teeth on your Spur Gear. To avoid this to some degree, fit locking nuts and a new motor mount from time to time, so the self taping screws that hold the motor in position have less chance to come loose.

   Ball joints always cause problems. For top level Radio Controlled model car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector breaking free could easily end your race, so better safe than sorry.

   Many New car kits come with Nylon and Sintered Brass Ring type bearings. My advice is to discard these before initial installation and buy a good Hop-up set of Shielded Steel Ball Bearings. Or if you are serious about your racing, Teflon or Ceramic Bearings.

   One final piece of advice about the Setup of your Car. Keep the Centre of Gravity as low as possible. Ride Height is all important. For On Road Drift/Touring cars the Ride Height should be no more than 5mm, for Buggys, Trucks, Truggys and Monster Trucks, as low as possible depending on the track conditions. If Body Roll is a problem, handling can be improved with the use of Stabilizers, Anti roll or Sway Bars, stiffer Tuning Springs and, or thicker Silicon Oil in the Dampers. Also find somewhere to mount the Transponder as low in the Chassis as possible.

For Car Setup Information check out our Hints and Tips page.

^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Caster

   Caster is basically the angle the steering kingpins or steering pivot points, leans back in relation to the horizontal when viewed from the side of the chassis.

   To test the effectiveness of your cars caster, place your model on a flat surface, point the front wheels straight ahead and push the chassis over to one side to simulate body roll when cornering. You will notice that as the car leans over, all four wheels also lean over in the same direction. Tires provide the most grip when the wheels are perfectly vertical and the full width of each tire is flat on the ground. Body roll pushes the wheels past the vertical and reduces the amount of tire contact. Now, if you turn the front wheels as if cornering and again push the chassis over, you will see that in this position, the front wheels are now more vertical, giving you better ground contact and therefore improved grip.

   Another effect of caster can be seen by disconnecting your steering servo and pushing your car along the floor. Because of caster and the kingpins leaning back, your car will naturally roll straight ahead.

   Obviously, the more body roll your car induces, the more positive caster you need to counter it. Buggys, Trucks and Truggys, because of their high ride height and long dampers have more body roll and therefore require more positive caster than on road cars, with their low ride height and shorter dampers.

   If you consider a corner as having three parts: An entrance, middle and an exit. Caster influences each of them.

   With a high degree of positive caster, as you enter the corner and body roll is at its greatest, steering is better. In the middle section, as body roll reduces, steering is less effective and some under-steer is induced, that will continue as you accelerate on corner exit.

   With a low amount of caster, steering response is improved in the middle section of low speed turns and will be more likely to over-steer on corner exit because of increased front end grip from the tires.

   Too little caster can result in difficult handling on corners and poor stability on the straights.

   Most modern RC model kits come with a standard caster setting that has been set for the best handling by the manufacturers. If you are new to the sport I would recommend you stick with this setting until you get a little more experience.

   Methods to adjust caster can vary from model to model. Sometimes it is as simple as moving the position of a plastic washer from one side of the top wishbone pivot bar to the other, or simply using a small clip. Models from some manufacturers often have specific caster blocks to change the angle and must be purchased separately.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Tires for RC Models

Rubber Tires:

   Rubber Tires ALWAYS should have either soft sponge or rubber inserts. They will not function as they should without them. And if you are totally serious about your racing, tires should be glued to the rims.

   You should also have at least three different compounds (Soft, Medium and Hard) for varying track temperatures in On Road tarmac racing Touring cars and varying pin sizes for carpet and Off Road racing Buggys and Trucks.


How to Mount Rubber Tires onto Wheels/Rims.

   Before mounting your Tires, I would recommend talking to the more experienced racers at your local club, as to what inserts they use. Even the top level racers rely on a bit of local knowledge on tracks they have never raced before.

1/   Once you have decided what inserts to use, position them inside the Tires ready to go onto the rims.

2/   You will need strong fingers to pull and maneuver the Tires over the rims, so you may need the help of an adult. I would recommend NOT using metal Tire levers or a spoon as they can not only damage the fragile plastic rims but can also put small tears in the rubber, that could cause problems later.
   The technique I recommend, is to first of all hook the Tire on one side of the rim, then using the thumb and forefinger, grip the Tire and pull it upwards and over into position around the middle of the wheel, then over to its final position on the far side so that the beading is seated in the spigot. then position the near side beading in the opposite spigot making sure the sponge (or rubber) insert is not trapped and positioned centrally.

3/   You have the option of either gluing or not gluing your tires in position. If the track you race at is not too grippy you can get away with it, but on high grip tracks there is the possibility the tire might pull away from the rim and ruin your race.
My recommendation is to glue them.
   Superglue is the thing to use. To do this, carefully pull the beading out of its seating, put on a spot of glue, then quickly push it back down. repeat this at least 6 times around each side of the wheel.
Superglue can be dangerous, so this is best done by an adult.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: