RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► CEN GSR-5.0.
RCScrapyard Radio Controlled Models
Flags

1/8 Scale Nitro Monster Truck:

CEN GSR-5.0 (Radio Controlled Model Review)


Navigation: Sitemap  ▶  Manufacturers  ▶  CEN

History, Info (and How To Set-up Tips) for the GSR 5.0:


  Introduced by CEN in 2008, the GSR 5.0 Monster Truck - # 9511 - is based upon a shaft-driven 4WD Dual Vertical Chassis design (DVC), with CVS (Constant Velocity Shafts), gear differentials, coil spring over oil filled dampers and Corsa 5.0cc Nitro Engine.

CEN GSR-5.0
▼ Scroll Down for More Images ▼


  To race the CEN GSR 5.0, it must be fine tuned to improve handling, provide responsive steering and give you the grip to cruise around corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our step by step procedure, will guide you to the best Set-up for your individual driving style.

ebay









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ CEN GSR 5.0 Chassiss ★
CEN GSR 5.0 Chassis


Buying a Used CEN GSR 5.0
Monster Truck (and What to look for)


   Buying a used CEN GSR 5.0 Nitro Monster Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the CEN website, or purchased separately on eBay. With an instruction manual, any problems with your model Monster Truck you may discover can easily be fixed.

Dampers
   When you receive your used CEN Monster Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those CEN models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your CEN GSR 5.0 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your GSR 5.0 model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your GSR 5.0 Monster Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Monster Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Monster Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Monster Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Monster Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The GSR 5.0 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your CEN GSR 5.0 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used CEN Monster Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your GSR 5.0 model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Gas / Nitro Engines

1/   New RC Gas Engines need running or "breaking" in before being used competitively. 2 or 3 tanks of fuel are usually enough, but don't over rev the engine and try to keep it cool, below 160 degrees F (71 degrees C)

2/   To maximise your RC Gas engines power, reduce air leaks as much as possible by using silicone sealant or high temperature gaskets where the carburettor and the exhaust manifold joins the engine block.

3/   As a rule, try to keep your engine temperature at around 210 F (99 C) and no higher than 225 degrees F (107 degrees C). If your engine temperature is higher than 225 F (107 C) try tweaking the mixture a little richer. If too cool (below 200 degrees F (93 degrees C)) tweak the mixture a little leaner.


Tell Tale Signs of a Lean burning engine.


1/   The engine dies at full throttle, or while simply idling.

2/   The Glow Plug element is white.

3/   The engine overheats (above 225 degrees F (107 degrees C))


Tell Tale Signs of a Rich burning engine.


1/   Blue smoke from the exhaust (tail) pipe.

2/   The smell of fuel from the exhaust (tail) pipe.

3/   Engine temperature below 200 degrees F (93 degrees C)


For More Setup Information check out my Hints and Tips page.






Hints and Tips

Tires for RC Models

Rubber Tires:

   Rubber Tires ALWAYS should have either soft sponge or rubber inserts. They will not function as they should without them. And if you are totally serious about your racing they should be glued to the rims.

   You should also have at least three different compounds (Soft, Medium and Hard) for varying track temperatures in On Road tarmac racing Touring cars and varying pin sizes for carpet and Off Road racing Buggys and Trucks.


How to Mount Rubber Tires onto Wheels/Rims.

   Before mounting your Tires, I would recommend talking to the more experienced racers at your local club, as to what inserts they use. Even the top level racers rely on a bit of local knowledge on tracks they have never raced before.

1/   Once you have decided what inserts to use, position them inside the Tires ready to go onto the rims.

2/   You will need strong fingers to pull and maneuver the Tires over the rims, so you may need the help of an adult. I would recommend NOT using metal Tire levers or a spoon as they can not only damage the fragile plastic rims but can also put small tears in the rubber, that could cause problems later.
   The technique I recommend, is to first of all hook the Tire on one side of the rim, then using the thumb and forefinger, grip the Tire and pull it upwards and over into position around the middle of the wheel, then over to its final position on the far side so that the beading is seated in the spigot. then position the near side beading in the opposite spigot making sure the sponge (or rubber) insert is not trapped and positioned centrally.

3/   You have the option of either gluing or not gluing your tires in position. If the track you race at is not too grippy you can get away with it, but on high grip tracks there is the possibility the tire might pull away from the rim and ruin your race.
My recommendation is to glue them.
   Superglue is the thing to use. To do this, carefully pull the beading out of its seating, put on a spot of glue, then quickly push it back down. repeat this at least 6 times around each side of the wheel.
Superglue can be dangerous, so this is best done by an adult.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: