RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Bolink 91 Sport
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Electric Rally/Touring Car:

Bolink 91 Sport (Radio Controlled Model Review)


Navigation: Sitemap  ▶  Manufacturers  ▶  Bolink

History + Information (and How To Set-up Tips):


  Introduced by Bolink circa 1991, the 2WD 91 Sport was available in a number of kit options, including: Less electrics - # BL-1367, Less batteries - # BL-1368, or assembled with a painted bodyshell - # BL-1367-P. Confusingly, these same model numbers were inherited from the previous Eliminator Sport.

  Various other kit options for the 91 Sport chassis were produced, including the Syclone Pick-up - # BL-1367-S, Jammin Jimmy - # BL-1363 - with a Chevy Blazer bodyshell and Radical Ranger - # BL-1366 - with a Ford Ranger bodyshell.

  Two different FRP plate chassis designs were produced (see images below), earlier versions with the old double 3 slot Eliminator 10 chassis, later replaced by the double 5-slot version. Both versions came with a ball differential, T-Bar, coil spring over kingpin front suspension, vertical silicone tube damper, alloy motor-mount and oilite bushings.

Bolink 91 Sport
▼ Scroll Down for More Images ▼


ebay









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Bolink 91 Sport ★
Bolink 91 Sport

★ Bolink 91 Sport Chassis ★
Bolink 91 Sport Chassis

★ Bolink 91 Sport Chassis ★
Bolink 91 Sport Chassis

★ Bolink 91 Sport ★
Bolink 91 Sport


Buying a Used Bolink 91 Sport
Touring Car (and What to look for)


   Buying a used Bolink 91 Sport Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the road.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the manufacturers website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Bolink Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Bolink models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Bolink 91 Sport is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your 91 Sport model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your 91 Sport Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The 91 Sport steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Bolink 91 Sport is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Bolink Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your 91 Sport model and good racing.




▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Ackerman

   So What is Ackerman?

   If you place your car on a table facing away from you and turn the steering to full lock to the left, you will notice the angle the left hand wheel has turned is more than that of the right hand wheel. That is the Ackerman effect.

   Moving your car to the edge of the table, with the wheels still on full lock, push it round a complete circle. What you will notice, is the diameter of the circle made by the inside wheel, is smaller than that of the outside wheel. This is a good thing.

   Consider what would happen if both wheels turned to the same angle. In this example, the inside wheel would have a tendency to drag sideways, making the car unstable and difficult to drive.

   The standard kit setting on the majority of RC Model cars, are generally pretty good for beginners, but when your experience increases, you will find out just what tuning your Ackerman can do for your driving style and why it can be helpful when setting up your car for any particular track.

   Some of the cheaper RC Models have fixed position steering links. Others have various methods to change Ackerman settings, like changing shims under the ball connector etc. These days, most modern cars allow you to adjust your Ackerman by lengthening or shortening the links by simply removing two screws and repositioning the links in relation to the front suspension arms.

   Lengthening the links, by adjusting the pivot points of the steering arms back towards the centre line of the rear axle, will give you Less Ackerman, providing you with more aggressive steering as you enter a corner. Useful on slippery tracks, to counter when the car tends to slide to the outside of the corner as you first turn into it.

   Shortening the links, by adjusting the pivot points of the steering arms more forward of the centre line of the rear axle, will give you More Ackerman, making cornering less aggressive, more predictable and improving car stability, better for high grip tracks, with smooth sweeping corners.

   How to implement these adjustments varies from model to model so you will have to refer to your manual for full instructions.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

RC Model Car Weight

   If you ever step up and enter a regional, national or international event in RC, you will find one specific rule concerning the weight of your car.

   At the time this article was written, the Minimum weight restrictions for 1:10 electric Touring Cars at different events, was between 1350g and 1500g. This includes your Motor, ESC, Receiver, Battery, Body Shell and the transponder.

   Out of the box you will find the majority of 1:10 Touring Cars, with everything onboard, are way over this Minimum weight and unless you are good enough to attract sponsors, getting your car down to anything approaching that minimum weight will be very expensive.

   There are things you can buy like micro ESC and Receivers. But Batteries and Motors are what they are and you have to work around them.

   To reduce the weight of your chassis, there are a number of things you can do. If the car you have is generally considered competitive enough, there are often carbon fibre main chassis, shock mounts and other alternative parts available, but they are expensive. And when the new version of your model comes out all the money you have spent is lost.

   The most cost effective weight reduction is the metal parts of your chassis. UJs, Drive and Pivot shafts and the like tend to vary from model to model, but turnbuckles can often be transferred and lengthened or shortened by using plastic ball connectors, so titanium is a consideration.

   Screw sets can also be transferred from car to car. Titanium screws and wheel nuts are always available, but there is a cheaper alternative Aluminium screws and nuts can reduce your cars weight cheaply, but be careful not to over-tighten them, aluminum is not as strong as titanium and can easily shear off if you are over zealous.

   Another weight reduction option is to drill holes along the base of the chassis. However, I do not recommend this. For one thing you are reducing the strength and making the chassis less rigid, but you are also raising the centre of gravity of your car, which can affect stability.

   If you do manage to get your car weight below the minimum allowed, this will give you an opportunity to add weight where you want it and lower the cars centre of gravity.

   One last tip: Knitting needles. When I first started in RC, money was tight and my dad came up with all kinds of ideas to reduce weight. He obtained a 3mm dye and found some of my mums old aluminum knitting needles that were just the right diameter. Having determined the length of the turnbuckles needed for my setup, he cut them to those lengths and threaded each end, so he could put plastic ball sockets on them. Adjusting them was a bit of a pain and they could be a bit fragile in crash situations, but they saved us lots of money over those early years.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: