RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Team Associated RC18B.
RCScrapyard Radio Controlled Models
Flags

1/18 Scale Electric Buggy:

Team Associated RC18B - 20105 (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Team Associated  >  Team Associated Timeline

All Manufacturers: Model Types  >  Buggys  >  1/18 Electric Buggys

History, Info (and How To Set-up Tips) for the RC18B


  Introduced by Team Associated in 2005, the 4WD RC18B Mini Buggy RTR - # 20105 - was based on the RC18T Truck chassis.

  The 18B is shaft driven on a molded plastic chassis, with ball differentials, coil spring over oil filled dampers, dogbone drive-shafts, narrow spoke wheels, pin-spike tires, a full set of ball bearings and came with a Super-370 motor, ESC, Radio system, battery and charger.

Team Associated RC18B
▼ Scroll Down for More Images ▼


  To race the Team Associated RC18B, it calls for fine tuning to attain better steering response and improve grip when cornering so you don't slide off the side of the track. Minute changes can make huge advancements. Our easy to understand list will show you how and lead you to the optimum Set-up to put you in front of the rest on the track.

  We give you all the basic information you need to guide you to the best Electric Motor for your RC18B and achieve the best Gearing, to get you in front on the track and keep you there.

  Find out how the worlds top professional RC racers get improved efficiency from their Bearings employing a number of sensible ideas. Find the way to avoid Radio interference, and basic instruction on how to Charge your Batteries, so they will last longer and provide improved power.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Team Associated RC18B Chassis ★
Team Associated RC18B Chassis

★ Team Associated RC18B Chassis ★
Team Associated RC18B Chassis


Buying a Used Team Associated RC18B Buggy (and What to look for)


   Buying a used Team Associated RC18B Electric Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Associated website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

Dampers
   When you receive your used Team Associated Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Team Associated models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Team Associated RC18B is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your RC18B model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your RC18B Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The RC18B steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Team Associated RC18B is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Team Associated Buggy came with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your RC18B model and good racing.


For More on how to Setup your Buggy, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Aerodynamics

   It is commonly understood that weight improves traction. If you have ever seen TV coverage of any kind of full size motor racing, you will have heard the terms, aerodynamics and down force. Well, they also relate to small scale models in exactly the same manner.

   Bodyshell aerodynamics for RC model cars is a science in itself and the wrong one could loose you the race. Back in my day the shell to have for 1:10 on-road, was the Alfa Romeo 156. The bodyshell that came with my Schumacher SST kit was a Peugeot 406, but that soon went into the bin when I got the Alfa. The difference in performance was amazing, but it wasn't a patch on the Frewer, Ferrari F50. The rear wing on that bodyshell was phenomenal; it was the fastest thing on the track, great for club racing, but to my cost, illegal for top level racing. Regulations stipulate that the rear wing should be no higher than the roof of the car, the Frewer wing was way too high, so another one was relegated to the "do not use" box.

   Off-Road models also benefit from aerodynamics and downforce, but to a lesser extent than on road models. The rear wing provides good downforce for better rear end traction and is discussed in detail in one of my other articles.

   Way back in 1994, a company named Tenth Technology produced a 1:10 buggy called the Predator. The design of the car was innovative to say the least, with inboard laydown cantilever operated shocks and extra low, almost flat bodyshell. The most eye-catching element of the design was the wings. Not only did it have a nice large wing on the rear, it also had one of a similar size at the front. It was one of those cars where the idea seemed good and the car was fast very fast and did once win the British Championship. The problem was its fragility. Any small knock damaging the front wing, made it un-drivable.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Anti Squat

   Described as the angle at which the suspension arms pivot in relation to the chassis, Anti Squat effects traction under acceleration.

   Considered to be at its most effective from a standing start, the handling and stability of the majority of modern day On Road and an increasing number of Off Road models, can be improved with a certain amount of anti squat, normally no more than around 3 degrees.

   Basically, more anti squat gives you more traction, but after a certain point, that advantage is lost and the car will become unstable when turning into high speed corners. For Off Road models anti squat can also improve how the car handles on bumpy tracks.

   Less anti squat allows the car to drop at the rear under hard acceleration, providing less traction, but more stable when cornering. If no anti squat is present, with the lower suspension pivot shaft being parallel to the chassis, steering will be sharp and can induce some over-steer.

   Most manufacturers have some anti squat on their car kits provided as standard and hop-up parts are generally available to change the anti squat angle, but more often, on a wide range of models, all that is needed is a washer or two under one side of the suspension pivot block. However, if the block is held in position using self tapping screws, it may be prudent to change them for slightly longer ones.

   If you are thinking of trying a different setting on your car, not just for anti squat, always remember to only make one change at a time. Too many changes to your set-up made at one time, can make it difficult, if not impossible, to determine which change you made gave you the result you desired.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: