RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Ansmann Mulisher.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Nitro Monster Truck:

Ansmann Mulisher (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Ansmann  >  Ansmann Timeline

All Manufacturers: Model Types  >  Monster Trucks  >  1/10 Nitro Monster Trucks

History, Info (and How To Set-up Tips) for the Mulisher


  Introduced by Ansmann Racing in 2007, the 4WD Mulisher Monster Truck (# 104000003) was based on the same chassis as the Reaper Buggy and ARN-1 Touring Car.

  For the Mulisher, the double deck chassis, employs coil spring over oil filled dampers, dogbone drive shafts and three gear differentials, one of which is mounted inside the centrally positioned gear assembly.

Ansmann Mulisher
▼ Scroll Down for More Images ▼


  To race the Ansmann Mulisher, it must be fine tuned to improve handling, provide responsive steering and give you the grip to cruise around corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our step by step procedure, will guide you to the best Set-up for your individual driving style.

  Our simple guide explains "run in" and what to look for as you tune the Nitro Engine for your Mulisher.

  Using plain language, our guide will show you how to avoid Radio interference, and Servo Twitch, by positioning your radio receiver and implementing the latest innovations. Find out how to reduce friction and improve the performance of your Ansmann Mulisher Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Ansmann Mulisher Chassis ★
Ansmann Mulisher Chassis

★ Ansmann Mulisher Chassis ★
Ansmann Mulisher Chassis


Buying a Used Ansmann Mulisher
Monster Truck (and What to look for)


   Buying a used Ansmann Mulisher Nitro Monster Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Ansmann website, or purchased separately on eBay. With an instruction manual, any problems with your model Monster Truck you may discover can easily be fixed.

Dampers
   When you receive your used Ansmann Monster Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Ansmann models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Ansmann Mulisher is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Mulisher model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Mulisher Monster Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Monster Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Monster Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Monster Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Monster Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Mulisher steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Ansmann Mulisher is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Ansmann Monster Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Mulisher model and good racing.


For More on how to Setup your Monster Truck, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.





















★ Ansmann Mulisher Chassis ★
Ansmann Mulisher Chassis


Hints and Tips

Choosing a Nitro Engine.

   Once you have made your choice of RC model, you need the right engine to get you where you want to be out in front.

   Touring Cars: Nitro powered Touring cars require a specific ability. Your first consideration should be the tail pipe. A number of models will take only a rear tail pipe configuration, but the majority will accept the more conventional side pipe.
   Beginners should consider something with a moderate amount of power and a rotary carburettor for easier controlled handling. For top level tarmac track racing or those with more experience, look for an engine with good low end torque that has a slide valve carburettor to give you fast acceleration out of the corners.

   Trucks and Monster Trucks: Unlike on road Touring Cars, Off Road Trucks and Monster Trucks don't need that bottom end torque, unless you like to do wheelies. So something less powerful with a rotary carburettor will provide you with the smooth acceleration and less wheel spin required for controlled dirt track racing.
   If tarmac is your thing, where grip is not a problem and you have the experience, a slide carburettor may suit your needs better. Tail pipe choice is generally a matter of preference. Most trucks will accept both side and rear configurations.

   Buggys: By far the most popular Off Road Nitro RC Models there is a wide choice of Buggys out there, many of which now come with engine included.
   Most Buggy engines use a slide valve carburettor, but if you are new to RC you may be better off trying a rotary carburettor. High low end engines with throw up plenty of dust but if you can't keep it on the track you are wasting your money. So something with less power may be better for you until you feel more confident.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Choosing a Transmitter

   When you first started in RC, you may have purchased a package that came with the car kit, motor, battery, charger, ESC and radio system complete. The transmitter was probably just a basic steer wheel, or stick type, with nothing more than forward, reverse, left, right and simple trim settings to centralise the servo and ESC.

   After a while, as your enthusiasm grows and your experience increases, you will want to move on to a better radio system, with more setting options, but where do you begin?

   Choosing the right transmitter is a personal thing. It has to feel right, have the balance you like, not be too bulky for your hand size and have all the features you might need to set up your car to your driving style.

   Transmitters these days are highly sophisticated pieces of engineering and once you choose you transmitter you will probably stick with it for the rest of your competitive career.

   Don't just go for the one you see in a review that looks and sounds like the best thing there could ever be and comes at a bargain price. Then when it arrives through the post and you get it in your hands it just doesn't have the feel you thought it would have. Sits awkwardly in your hands and is so complicated to set up you need a university degree to understand it.

   Talk to the experienced racers at your local track, ask them their opinion, see what their transmitter is like and if they will allow you to, hold it in your hands and see how it feels. All the best buys in life are made by recommendation. Then, once you have some idea what you are looking for, look on the internet for that model to get the best price, or go to a dealer and check out the latest models.

   Frequency choice depends on where in the world you live and what form of RC you are into. Fortunately, most of the top end transmitters can change to different frequency ranges by simply fitting a different module, so if you ever move up to an international level, you don't have to buy a new transmitter, just a module and receiver.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: