RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Ansmann Kryptonite-Pro.
RCScrapyard Radio Controlled Models
Flags

1/8 Scale Nitro Truck/Truggy:

Ansmann Kryptonite-Pro (Radio Controlled Model)


Navigation: Sitemap  >  Manufacturers  >  Ansmann  >  Ansmann Timeline

All Manufacturers: Model Types  >  Trucks/Truggys  >  1/8 Nitro Trucks/Truggys

History, Info (and How To Set-up Tips) for the Kryptonite Pro


  Introduced by Ansmann circa 2011, the 4WD Kryptonite Pro Truggy - # 113000008 - came as a kit, with a wide number of upgrades.

  The model was shaft driven, on an alloy plate chassis, with 3 x gear type differentials, coil spring over oil filled dampers, universal joint drive-shafts and ball bearings.

Ansmann Kryptonite-Pro
▼ Scroll Down for More Images ▼


  To race the Ansmann Kryptonite Pro, it must be fine tuned to improve handling, provide responsive steering and give you the grip to cruise around corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our step by step procedure, will guide you to the best Set-up for your individual driving style.

  Our simple guide explains "run in" and what to look for as you tune the Nitro Engine for your Kryptonite Pro.

  Using plain language, our guide will show you how to avoid Radio interference, and Servo Twitch, by positioning your radio receiver and implementing the latest innovations. Find out how to reduce friction and improve the performance of your Ansmann Kryptonite Pro Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Ansmann Kryptonite Pro ★
Ansmann Kryptonite Pro

★ Ansmann Kryptonite Pro Chassis ★
Ansmann Kryptonite Pro Chassis

★ Ansmann Kryptonite Pro Chassis ★
Ansmann Kryptonite Pro Chassis


Buying a Used Ansmann Kryptonite Truggy (and What to look for)


   Buying a used Ansmann Kryptonite Nitro Truggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Ansmann website, or purchased separately on eBay. With an instruction manual, any problems with your model Truggy you may discover can easily be fixed.

Dampers
   When you receive your used Ansmann Truggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Ansmann models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Ansmann Kryptonite is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Kryptonite model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Kryptonite Truggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Truggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Truggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Truggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Kryptonite steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Ansmann Kryptonite is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Ansmann Truggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Kryptonite model and good racing.


For More on how to Setup your Truggy, check out my Hints and Tips page.


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Droop

   When you pick up your RC model car, the suspension arms naturally drop, this is termed as Droop and should be equal from side to side, but can vary from front to rear.

   Setting the amount of droop, or suspension movement, can dramatically change the handling of your car by limiting the transfer of weight from one side of the car to the other.

   Basically, increasing the droop at the rear of the car can improve cornering grip at the front and increasing droop at the front of the car, improve cornering grip at the rear. The amount of effectiveness of this setting does in general depend on a number of other setting factors your car may have to suit your personal driving style. Also, adding any droop will increase body roll.

   Off road models obviously have the need for more droop than On road cars, especially on bumpy tracks where a large amount of suspension movement is needed to simply keep the wheels on the track, or the car will become unstable and un-drivable. Lower droop settings for smoother, high grip tracks on the other hand can be advantageous, but don't overdo it.

   On road cars can achieve good results from small changes in droop, on tarmac and on carpet. In general they are also easier to adjust for droop than their off road cousins.

   Limiting the amount of droop can be achieved in a number of ways, but by far the easiest is more often seen as a standard setting option for On road cars and is achieved by simply turning a screw, located on the suspension arms, that comes up against the chassis.

   For Off road models and those On road cars that do not have the above option, droop can be set by positioning a specific length of plastic tube over the damper shaft, just below the piston this of course means stripping and rebuilding each damper with the new setting, which can be messy, especially in the middle of a field. Some of the top drivers used to get around this by simply having a number of different sets of shocks, with all the settings they might need, but for us mere mortals, this of course isn't a realistic option.

   If you are close to what you consider to be your optimum droop setting, you can fine tune this by simply screwing on or off the plastic ball connector at the end of the shock shaft. You could also have different length ball connectors that you could easily change.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Bearing Seals

   If you were to ask anyone with a modicum of experience in RC, they will tell you that the best modification you can make to a basic RC model, is to add a set of ball bearings.

   Quite a few of the entrance level models at the time this article was written, come with plastic and sintered brass bushings (ring type bearings). If these bearings are installed in the model and coated with grease as advised in the car manual, dust and grit can be caught in that grease and be dragged into the bearing where it can abrade the shaft that spins in it and it won't be long before it becomes a very sloppy fit, causing all kinds of problems.

   But what should you look for when buying bearings? There are a number of types of seal used on ball bearings and there is much debate concerning which is the best for RC.

   Rubber and Cork bearing shields are two of the more common types available, but although they are very effective when it comes to preventing dust and grit entering the bearing, they also create more drag in the bearing due them rubbing against the bearing to create friction. For this reason, if I wanted to race my model at any level and that model was fitted out with rubber or cork shielded bearings, I would change them ASAP.

   Steel and Teflon bearing shields may not be as effective as the rubber shielded versions, but they don't rub on the bearing, so little or no friction is created. The problem with this kind of bearing of course is that they need much more maintenance and are often more expensive.

   Basic shop bought bearings generally come packed with grease for their lubrication. However, if you want to have your bearings spin freely; grease is not the best thing to use. So, before you install your new bearings in your car, the first thing you need to do is clean out the grease with something like isopropanol and replace with thin oil.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: