RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Academy Plastic Model Co Genesis Coupe
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Electric Rally/Touring Car:

Academy Genesis Coupe (Radio Controlled Model Review)


Navigation: Sitemap  ▶  Manufacturers  ▶  Academy  ▶  Academy Timeline

History + Information (and How To Set-up Tips):


  Introduced by Academy Racing Team circa 2009, the 2WD Genesis Coupe - # 15113 - came RTR with a 540 motor, ESC, battery and radio system.

  The model is based on a pan car type chassis, with motor-pod and coil spring over damper.

Academy Genesis
▼ Scroll Down for More Images ▼


  To race the Academy Genesis, it requires a high level of tuning for improved stability when cornering, to keep it on the track and give you more grip under acceleration. Even the smallest change in your cars settings can make a Big difference. Our simple to follow instruction chart will show how to attain the best Set-up for your personal requirements.

ebay









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Items For Sale:






Flags

★ Academy Genesis Chassis ★
Academy Genesis Chassis


Buying a Used Academy Genesis
Touring Car (and What to look for)


   Buying a used Academy Genesis Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the road.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Academy website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Academy Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Academy models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Academy Genesis is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Genesis model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Genesis Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Genesis steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Academy Genesis is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Academy Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Genesis model and good racing.




▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide


^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.


















Hints and Tips

Sway Bars

   On most forms of RC model cars, Sway Bars, also referred to as Stabilizers, Torsion Bars, or more commonly in some parts as Anti Roll Bars, are often nothing more than a short length of spring steel, clamped to the chassis or sometimes the gearbox of the car, extending out to the lower wishbones direct or connected to the wishbones using short adjustable or fixed length links and ball joints, depending on their position.

   The principal behind the Sway Bar is simple. As the car enters a corner, weight is transferred to the outside wheels, the chassis rolls due to inertia and the suspension dips and grip on the inside wheels is reduced. In an effort to counter this dipping effect and transfer some grip back to the inside wheels to improve traction as you exit the corner, the sway bars transfer the dip of the outside, to pull down the inside wishbones, improving grip on the outside wheels and improving overall stability.

   Sounds complicated I know, but for some tracks sway bars can be a useful tool when you have exhausted all other options to correct your handling problems.

   Tuning your Sway Bars is quite easy. Some manufacturers do offer colour coded tuning sets with varying thicknesses of spring steel wire, but the best way is to change the position the bar is attached to the wishbone, or on some variations you have the option of positioning the link on the Sway Bar itself. By simply moving a small collet clamped along the short length of the bar. Closer to the central pivot point reduces the leverage of the bar and effectively increasing its resistance, further away from the pivot point reducing resistance. More fine tuning can be achieved by adjusting the length of the turnbuckle link (if available) to pre load the bar.

   Personally, before I ever installed any sway bars I would always try changing damper tuning springs and oil viscosity settings, especially if the track was uneven and bumpy, in which case the effectiveness of the bars was minimal if at all.

   For those more into Drifting, Sway Bars can be an easy way to fine tune your car. A single turn on the turnbuckle links can be a way to simply increase or decrease wheel traction that minute amount you need to get the perfect balance.

   For more on how to use Sway Bars check out our Set-up tips page linked below.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Tires for RC Models

Sponge (Foam) Tires:


   Sponge Tires can be purchased either pre mounted, glued and trued on the rims, or separately. Fitting the Tires onto the rims can be messy, so here are a few tips to make it a bit easier.
   If you are fitting new Tires on old rims, make sure the old sponge Tire is completely removed. To do this, I recommend using a wood lathe and apiece of wood, at least 300mm long and more than the width of your wheels, with medium grit emery paper stuck to it ... sand paper will also work, but emery is harder wearing ... This will also be used for truing a wheel. (Described later)

How to Mount and Glue Sponge Tires onto Wheels/Rims.


1/   Mount the Tires on the rims. Make sure they are reasonably tight on the rims, too loose and you might have problems.

2/   I find this to be easier if either in the lathe, or on the car itself. (but be careful with that glue)
  Using your thumb and forefinger, lift up the Tire off the rim, then using a small spatula or a thin piece of rigid wood or plastic dipped in glue (I recommend Evo-Stik, Impact Adhesive) slip it in the gap, making sure both the Tire and the rim are smeared. Then lower the Tire back onto the rim and press it down. Turn the Tire approximately 60 degrees and repeat.

3/   Depending on the width of the Tire you may need to repeat the process on the inside also.


How to True Sponge Tires.


   Truing Sponge Tires is essential if you are serious about racing competitively. To do this you will need the piece of wood, as described earlier and a good pair of vernier or digital calipers.
   Sponge Tires will always wear unevenly, weather you race on Carpet or Tarmac. The outside wheels will always end a race smaller than the ones on the inside, so after each race I recommend swapping them over (unless you are fortunate to have a new set for each race) and dont forget to adjust the steering trim on your transmitter before the next race.

1/   Before starting, check each mounted Tire for diameter and order them smallest to largest. Start with the smallest and mount it in the lathe.

2/   Make sure you are wearing safety glasses before you start this procedure: Lay the sanding wood under the Tire so that it can be pivoted up from behind onto the Tire. Start the lathe spinning, so that as you stand infront of the Tire, it is rotating downwards. Slowly lift the sanding wood and try to hold it ridged as it comes up against the Tire. There will be a high point on the Tire that if you hold the bat rigid enough will eventually wear down until the Tire appears completely concentric. at this point stop the lathe and measure the diameter on the inside and outside of the width. If needs be, repeat the process until satisfied.
Repeat for each Tire, matching them in pairs for diameter.
If considered necessary also trim the sides.


For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: