RCScrapyard ► Radio Controlled (RC) Models, Parts and Spares ► Kyosho Inferno MP-5. For Sale in The USA.

Tamiya Buggys RCScrapyard: New, used, second hand radio controlled models, parts and spares.
Established 1999
Tamiya Monster Buggy
Site Search
Complete RC Model Listings    USA - Sitemap UK - Sitemap AU - Sitemap CA - Sitemap ES - Mapa del sitio IE - Sitemap DE - Sitemap FR - Plan du Site IT - Mappa del sito NL - Sitemap AT - Sitemap CH - Sitemap    From Around The WORLD

1/8 Scale Nitro Buggy:

Kyosho Inferno MP-5


USAUS UKUK AUSAU CANCA ESES IEIE DEDE FRFR ITIT NLNL ATAT CHCH

How To Set-up, Hints and Tips for the Kyosho Inferno MP-5:

  If you want to get all you can from your Kyosho Inferno MP-5, it needs to be tuned to perfection for better stability, precise steering and provide enough grip to keep you on the track when going around tight bends at high speed. Even the smallest adjustment can change the feel of a car, and our simple to follow instructions will guide you to the best Set-up to get you to the front and keep you there.
  Our basic instructions will help you set-up and fine tune the Nitro Engine for your Inferno MP-5.
  With a few simple tips, we will show you how to easily avert Radio interference, and Servo problems, by simply repositioning the receiver or using some of the latest developments. Learn how to combat friction and get more from your Kyosho Inferno MP-5 Bearings with a few common sense hints and tips.


★ Kyosho Inferno MP-5 ★
Kyosho Inferno MP-5






★ Radio Controlled Model Accessories: ★
Gas/Nitro Engines
Nitro Engines
Glow Plugs
Glow Plugs
Starters
Starters
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Radio Transmitters etc
Radio Equipment















USA

Kyosho Inferno MP-5: For Sale in the USA

Logo

★ Kyosho Inferno MP-5: ★


USA - Sitemap UK - Sitemap AU - Sitemap CA - Sitemap ES - Mapa del sitio IE - Sitemap DE - Sitemap FR - Plan du Site IT - Mappa del sito NL - Sitemap AT - Sitemap CH - Sitemap


Buying a Used Kyosho Inferno MP-5 Buggy.


   Buying a used Kyosho Inferno MP-5 Nitro Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase they can often be downloaded from the Kyosho website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

   When you receive your used Kyosho Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for anything broken that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten. Next, for those Kyosho models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Kyosho Inferno MP-5 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Inferno MP-5 model, fit an under guard to stop dirt and gravel entering the chassis.

   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Inferno MP-5 Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

   The Inferno MP-5 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Kyosho Inferno MP-5 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

   If your used Kyosho Buggy comes with plastic and sintered brass ring type bearings, check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Inferno MP-5 model and good racing.


For More on how to Setup your Buggy, check out my Hints and Tips page.


^ TOP ^


    ★ RC Information and Advice ★    





Click Here


Not Here?
Maybe Tomorrow.
♥ Add This Page to your Favorites (Ctrl+D) ♥

★ Radio Controlled Model Accessories: ★
Gas/Nitro Engines
Nitro Engines
Bearings and Bearing Sets
Bearings
Body Shells
Body Shells
Radio Transmitters etc
Radio Equipment
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Electronic Speed Controllers
ESC
Battery Packs
Batteries + Chargers
Electric Motors
Electric Motors






Hints and Tips


Bearings

   If you are serious about your racing, looking after your bearings is essential if you are to remain competitive.
   My own experience is in both Off and On Road, National and International Car racing, but most of these tips could be useful to all forms of RC.

   Shields: The main problem with Ball Bearing Shields is they create friction, and obviously the more you can reduce friction, the more efficient your bearings will be, so here's a tip that does just that.
   Wheel Bearings always come in pairs, positioned side by side. If you think about it, the two inside shields on each bearing are not required, so ... you can remove them using a small jewelers screwdriver ... simple. And in one fell swoop you have halved your wheel bearing friction.

   Cleaning: All Bearings need to be cleaned from time to time. Depending on how focused and competitive you are, this can be as often as after each race meeting, or just once or twice a year ... For Club Meetings once or twice a year might be all you need if you are easily beating your competition, but for the BIG meets you need that extra 5% or 10% just to be up with the rest.
What you need is a small glass jar, a jewelers screwdriver, an old tooth brush and some Isopropanol.
Remove the shields, then drop the bearings in the jar, add some Isopropanol, pop on the lid and shake well. Empty them out, give them a good brushing and make sure they spin free then repeat the process. Clean the shields separately. Once you are satisfied, lay them on a piece of kitchen roll and allow to dry.

   Lubrication: The arguments I have had about what lubrication to use you wouldn't believe. Some of the top racers of my day swore they didn't use any at all, but cleaned out the original lubrication and ran them dry ... they also admitted to fitting a new set after each meeting ... well, they were getting them for free.
My tip is, yes even with a new set of bearings, clean out the original lubrication (as described above) and with one shield in place use the thinnest oil you can find ... I recommend ZX1 (Zed Ex One) or sewing machine oil.

For More Setup Information check out my Hints and Tips page.






Hints and Tips

Wheel Balancing

   At the tender age of 17 I passed my driving test. Of course, the first thing I did was to dash over to my girlfriends house, and take her out to a long straight stretch of road close by where the boy racers would often congregate. No one was around that day, so the road was relatively quiet. I slowly went through the gears and we reached 65 with no problems, but as we got closer to 70, my hands sensed a small vibration on the steering wheel. By the time we reached 75, the steering wheel and the whole car was vibrating hard. I remember my girlfriend screaming for me to "slow down," Which I did of course and tried to laugh it off.

   Back home I told my dad what had happened and he reminded me, that just the week before we had put on a new set of front tires and it must be the balance that is out. Sure enough, after the wheels were balanced, 85, 90, was not a problem, the car drove perfectly.

   So, when I got deeper into RC, that memory returned and now I balance all my wheels.

   These days, wheel balancing equipment for RC cars is available from most RC model shops, but back then I had to make my own using the rear end of an old Tamiya F1 car. Here's how I did it.

   With the tire and insert mounted and glued, the wheel was fitted onto my home made balancer and allowed to settle. I would then gently turn the wheel through 90 degrees and again allow it to settle. Obviously the heavy side of the wheel would drop to the bottom due to gravity. Once I was satisfied, I would then make a mark on the rim with a felt tip pen at the top of the wheel where it came to rest. Removing the wheel I would mix a small amount of plastic resin and press a tiny amount of this into a recess on the wheel on the side where I made the mark. The whole process was then repeated until I was totally satisfied.

   I was amazed just how out of balance some of those wheels were and how much a small thing like that can make a difference on the track.

For More Setup Information check out my Hints and Tips page.








Trend Times Toy Store


On/Off Road
RC Models:

Other RC Models:

Radio Equipment:

Accessories:
Buggys

Formula One

Monster Trucks

Rock Crawlers

Touring/WRC/Drift Cars

Trucks/Truggys



Airplanes

Boats/Ships

Helicopters

Motorcycles

Submarines

Tanks



Crystal Sets

Receivers

Servos

Transmitters



Batteries

Battery Chargers

Bearings

Body Shells

Dampers (Shocks)

Electric Motors



ESC

Nitro Engines

Pinion Gears

Spur Gears

Tires

Wheels