RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Duratrax Maximum ST Pro.
Tamiya Buggys RCScrapyard: New, used, second hand radio controlled models, parts and spares.
Established 1999
Tamiya Monster Buggy
Search Site Search
Radio Controlled Models    Flags    From Around The WORLD

1/10 Scale Nitro Truck/Truggy:

Duratrax Maximum ST Pro - DTXC0090 / DTXD90**


Navigation: Sitemap  >  Manufacturers  >  Duratrax

All Manufacturers: Model Types  >  Trucks/Truggys  >  1/10 Nitro Trucks/Truggys

History, Info and How To Set-up Tips, for the Maximum ST Pro:

  Introduced by Duratrax in 2000, the 2WD Maximum ST Pro Stadium Truck, was available Pre-Built - DTXC0090 - without a radio system, or RTR - DTXD90** - with a Torq 16 engine, and AM radio system.

  The model was based on an alloy plate chassis, with a gear type differential, coil spring over oil filled dampers, universal dogbone drive-shafts, 2-Speed transmission, and a full set of ball bearings.

  To race the Duratrax Maximum ST Pro, it requires time and patience, to tune and adjust for improvements in handling and steering ability, and to get the grip you need to stay on course when manoeuvring around tight, slippery corners. A little can be a lot when it comes to changing your cars settings, and our easy methodical directions will guide you to the best Set-up to help you win and keep you winning.

  Our easy to understand guide will show you how to adjust the Nitro Engine for your Maximum ST Pro.

  Employing a number of sensible ideas, find out how you can avoid Radio interference, and problems with your Servo, by making a few changes to the layout of your equipment in your chassis. Discover what the top drivers do to improve the efficiency of their Duratrax Maximum ST Pro Bearings with a few common sense hints and tips.





★ Duratrax Maximum ST Pro ★
Duratrax Maximum-ST-Pro






★ Radio Controlled Model Accessories: ★
Gas/Nitro Engines
Nitro Engines
Glow Plugs
Glow Plugs
Starters
Starters
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Radio Transmitters etc
Radio Equipment






   Radio Controlled Models   
RC Touring/WRC/Rally Cars
Touring - WRC - Drift
RC Buggys
Buggys
RC Trucks
Trucks - Truggys
RC Monster Trucks
Monster Trucks









Duratrax Maximum ST Pro:
Models and Spare Parts, For Sale in the USA





Flags

★ Duratrax Maximum ST Pro ★
Duratrax Maximum ST Pro

★ Duratrax Maximum ST Pro ★
Duratrax Maximum ST Pro

★ Duratrax Maximum ST Pro Chassis ★
Duratrax Maximum ST Pro Chassis


Buying a Used Duratrax Maximum ST Pro Truck.


   Buying a used Duratrax Maximum ST Pro Nitro Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Duratrax website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover can easily be fixed.

   When you receive your used Duratrax Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for anything broken that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten. Next, for those Duratrax models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Duratrax Maximum ST Pro is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Maximum ST Pro model, fit an under guard to stop dirt and gravel entering the chassis.

   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Maximum ST Pro Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

   The Maximum ST Pro steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Duratrax Maximum ST Pro is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

   If your used Duratrax Truck comes with plastic and sintered brass ring type bearings, check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Maximum ST Pro model and good racing.


For More on how to Setup your Truck, check out my Hints and Tips page.


^ TOP ^


    ★ RC Information and Advice ★    









★ Radio Controlled Model Accessories: ★
Gas/Nitro Engines
Nitro Engines
Bearings and Bearing Sets
Bearings
Body Shells
Body Shells
Radio Transmitters etc
Radio Equipment
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Electronic Speed Controllers
ESC
Battery Packs
Bats + Chargers
Electric Motors
Electric Motors






Hints and Tips

Damper Pistons

   When you first build your RC model, you will sometimes find that there are a number of different pistons in the kit, with varying numbers of holes or hole sizes in them. Generally, the manufacturer will suggest one particular piston in the car manual, and may provide you with a mid range oil weight, but depending on the type of terrain you intend to race your model, their suggestion may not be the best for your needs.

   When it comes to tuning your dampers there are basically two things you need to know about pistons. "Pack" and "Static Damping".

   Pack, is the speed your damper reacts to any quick compression and can be considered to be a consequence of the size or number of holes in the piston. Smaller holes, more pack, larger holes, less pack.

   Static Damping is the amount of resistance you sense when slowly pulling or pushing the piston rod in and out of the damper. As with pack, this is related to the number or size of the piston holes. Larger holes, less static damping, smaller holes more static damping.

   Setting up your dampers is a matter of trial and error. With the car in full race mode, that means with everything installed, place it on a table, then pick up the rear of the car, raising it around six inches and drop it onto the table. The chassis should dip slightly below then back up again to the pre-set ride height, in one smooth movement. If instead, it slaps down onto the table, the pack of your dampers is not enough. In this instance, depending on the setup you are testing, you have two options, thicker oil or smaller holed pistons. If when you do the test the dip is hardly any, then the pack is too hard and you should try thinner oil or bigger holed pistons. Repeat this process for the front of the car. Finally, with both ends adjusted, pick up the entire car and drop it from the same height. Both ends should respond equally when dropped, if not, change your pistons or oil weights until they do.

   After your basic setup, you then need to test your car on the track. If the rear of the car tends to hop excessively over small bumps, the rear dampers have too much pack. You need to change the pistons on the rear for larger holes, and also use thicker oil to maintain static damping. If the car chassis bottoms through small bumps and landing on jumps, the pack is not enough. In this instance, change for smaller holes and thinner oil.

   If the car lands nose up from a jump, this is indicative of the front dampers having too much pack. These should be adjusted as described above to keep the car static damping in balance. Nose down obviously means not enough pack ..

   I hope this article has been helpful. Good luck and good racing.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Glow Plugs

   Nitro Engines for RC Models, use a system to ignite the fuel mixture, that simply employs a wire coil in a small housing called a Glow Plug. To start the engine, a battery powered Starter, or Glow Igniter is connected to the Glow Plug, and electric current heats the coil to white hot, so that when you pull start your engine, the air - fuel mixture in the cylinder is ignited. With the engine now running, the starter is no longer required. Heat generated under compression is enough to keep the coil element hot enough to keep the engine running.

   At some point, the Glow Plug originally supplied with your Engine will invariably burn out, so you will have to purchase a replacement. If your engine isn't too old you should be able to obtain a similar one, but if the manufacturer is no longer in business you may have a problem.
   If you still have the instruction book that came with your engine you may find there are a number of optional plugs available. Most Plugs generally have a code, indicating the plug elements effective operating temperature. These codes vary from manufacturer to manufacturer so be wary if you need to consider a plug from a different Manufacturer than that of your engine.

   Basically, Smaller engines run better with Hot Plugs, and Larger engines prefer Cold.
   Nitro fuels for RC engines normally have between 10 to 40 percent Nitromethane (CH3NO2). If you use fuel with a high proportion of Nitro, err towards Cold Plugs. Less Nitro, Hot.

   For example, For a .12ci (2.1cc) Nitro Engine, burning High percentage nitro fuel, a mid range plug would be best for performance.
   While a .21ci (3.5cc) Engine, with Low percentage nitro fuel, would prefer a Hot Plug.

   One more thing you may at some point consider when determining the right plug, is the compression ratio of your engine.
   By removing one of the Head shims you can Increase the compression. More shims, Lower compression. This option is not something I would recommend to those with little knowledge, so if you want to try this please be sure to ask someone with more experience before risking your expensive engine.
   High compression ratio engines run better with Cold Plugs. Conversely, Low compression ratio engines need Hot Plugs.

   If for some reason you use the wrong plug, you will soon know by how the engine runs. With too Hot a Plug, the engine will overheat and could damage your engine. If you hear the engine miss fire at high revs, and you see pit marks on the cylinder head and piston, try either a cooler plug, add a shim to the head, or lower percentage Nitro fuel.

   If your Plug is too cold, your engine will idle poorly, lose acceleration and top speed. You will also notice the smell of fuel from the tail pipe. However, be wary, this could also be because of a rich fuel mixture.

For More Setup Information check out my Hints and Tips page.









On/Off Road
RC Models:

Other RC Models:

Radio Equipment:

Accessories:
Buggys

Formula One

Monster Trucks

Rock Crawlers

Touring/WRC/Drift Cars

Trucks/Truggys



Airplanes

Boats/Ships

Helicopters

Motorcycles

Submarines

Tanks



Crystal Sets

Receivers

Servos

Transmitters



Batteries

Battery Chargers

Bearings

Body Shells

Dampers (Shocks)

Electric Motors



ESC

Nitro Engines

Pinion Gears

Spur Gears

Tires

Wheels