RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Tamiya MAN TGX 26.540 6x4 XLX. ITEM: # 56325
RCScrapyard Radio Controlled Models
Flags

Tamiya MAN TGX 26.540 6x4 XLX - # 56325 (Radio Controlled Model Review)

1/14 Scale Electric Tractor Truck - TT Chassis

  Released by Tamiya on November 1, 2010, the MAN TGX 26.540 6x4 XLX (#56325) kit, is of the Truck which made its debut at the 2007 European Transport Road Show in Amsterdam and was the winner of the 2008 Truck of the Year award. A 4-channel radio system, battery, charger and ESC are required to complete.

Tamiya MAN TGX 26.540 6x4 XLX - 56325
▼ Scroll Down for More Images ▼


  The shaft driven model is based on a rigid alloy ladder frame chassis, with rear twin axle, gear type differentials, leaf-spring suspension, friction dampers and 3-speed gearbox. A Multi-Function Unit is available separately, to recreate fully controllable light, sound and vibration actions. 9 types of ultra-bright LED lights include headlights, fog lamps and turn signals. 24 types of digitally-recorded sound effects include air-brake, shift change and reverse signal. Vibration unit enables realistic vibrations synchronized with engine sound effects.

  A 540 brushed Motor is included and Plastic bush type bearings, that after a short while, when dust and grit get into them, can actually wear into the metal drive shafts that spin in them - we recommend these should be replaced by a full set of steel shielded ball bearings.


      Rating: 44 Stars out of 5 Reviewed by: RCScrapyard     Manual.

ebay




Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors












Flags


Tamiya MAN TGX 26.540 6x4 XLX
Tamiya MAN TGX 26.540 6x4 XLX Chassis

Tamiya MAN TGX 26.540 6x4 XLX
Tamiya MAN TGX 26.540 6x4 XLX Chassis

Tamiya MAN TGX 26.540 6x4 XLX - Chassis
Tamiya MAN TGX 26.540 6x4 XLX Chassis

Tamiya MAN TGX 26.540 6x4 XLX - Gearbox
Tamiya Gearbox


Buying a Used Tamiya MAN TGX 26.540 6x4 XLX
Tractor Truck (and What to look for)


   Buying a used Tamiya MAN TGX Electric Tractor Truck, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Tractor Truck you may discover, can easily be fixed.

Dampers
   When you receive your used Tamiya Tractor Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Tamiya MAN TGX is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your MAN TGX model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your MAN TGX Tractor Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Tractor Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Tractor Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Tractor Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Tractor Truck racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Servo Gears
   The MAN TGX steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Tamiya MAN TGX is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Tamiya Tractor Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your MAN TGX model and good racing.


▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide














^ TOP ^












Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks












Hints and Tips


Electric Motors for RC Models

Brushless Motor Basics

   Choosing the right Brushless motor for your needs can be a daunting task for those new to Radio Controlled Models. If you have a local club perhaps you could ask some of the more experienced members for their advice, but a little basic knowledge about the subject, so you know what questions to ask is always useful.

   All Brushless motors are rated by Kilovolts (KV) and is an indication of the revs per minute (RPM) that particular Motor can attain running freely, under no load conditions, per Volt of input.

   For Example: To calculate the Maximum RPM of a Motor listed at 4000 KV, connected to a 7.4 Volt Battery, simply multiply the two: 4000 x 7.4 = 29600 RPM.

   The two main types of Brushless Motors used in RC are Sensored and a Sensorless Motors.
   Sensored Motors can be connected directly using s cable, to the Electronic Speed Controller (ESC). The ESC is then able to monitor the performance of the Motor and regulate Current output, to attain smooth, controlled acceleration. Advance and Retard timing is made automatically by the ERSC to change torque when exiting corners and give you more RPM for long straights.

   Sensorless Motors can only be set manually for Advance and Retard timing and once that setting is made you have to stick with it. For obvious reasons, Sensorless motors are cheaper to buy than the Sensored type: Ideal if you just want to bash around in the back yard, but not so much if you are serious about your racing.

   Brushless Motors, need a reasonable amount of maintenance if they are to remain competitive. For top level racing I recommend you strip, clean and re-oil the bearings every 2 or 3 meetings (Check out our "get the best from your bearings" section).
   Gearing your motor correctly for any given track is always important. (Check out my Gearing tips on the Pinions Section of this site) A cool motor is an efficient motor. As your motor heats up towards the end of a race, it will loose efficiency. Gearing correctly can avoid this problem to some degree and simply following my simple guidelines, described in the aforementioned article can help you not only keep your motor running efficiently, but help you stay in front of your opposition.

   One last tip .. When re-building your Brushless Motor, to safely replace the Rotor, use a rolled up piece of paper and place it into the Can. This will protect your rotor against damage. Then carefully remove the paper before replacing the endbell.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Driving On Road

   The basic driving style most commonly used for all forms of on road, tarmac and carpet racing, involves using the full width of the road available and cutting each apex as tight as possible, whilst keeping complete control of the car on the track. The style, often referred to as "Rounding" looks quite simple to those watching, but to get it right needs good hand eye coordination and lots of practice.

   Consider a 180 degree turn. As you enter the corner, start with the car positioned close to the outside of the track, then as you approach the corner brake hard, but not too hard, just enough to slow the car so you maintain control and smoothly guide the car across the point of the apex, gently sweeping round until you are approximately 75% around the corner. At this point, gradually increase the throttle out of the corner, under full control and guiding the car to the opposite outside line. By the time the car is pointing straight on the track, you should be at almost full throttle, before you brake hard again for the next corner.

   Developing this driving style comes in stages. Don't try to run before you can walk, install a low powered motor and practice, practice, practice until it becomes second nature. Then, as your skills improve, try something with a little more power.

   Initially set your transmitter to aggressive breaking and gradually reduce this as you get the feel of the car around the corner. Remember, the faster you enter a corner, the faster you exit it.

   When you first try out this style in a race, be patient, keep the car smooth and controlled. Remember the story about the hare and the tortoise? Well, believe me, when you first start in RC, it works.

   To make this driving style work, the car needs to have the right tires, inserts and a low centre of gravity. Adjust the suspension to provide only a small amount of body-roll and set-up guide linked below to help you set your car to suit your driving style.

   Avoid over-steer, always aim for a little under-steer. Grip is the keyword for the rounding style of driving, but not too much grip. Slicks for outdoor racing and a worn set of Hawgs I found to be best for carpet racing. If your car rolls sideways off the track as you enter the corner, try a harder tire compound, or change the damper springs or oil weights as suggested in our set-up guide. Good luck and good racing.

   If the style you are looking for is to drift slide your car around the corners, I would recommend you perfect the rounding style first, then check out my other hints and tips to learn how.

For More Setup Information check out my Hints and Tips page.








^ TOP ^


On/Off Road
RC Models:

Radio
Equipment:

Accessories: