RCScrapyard ► Touring Car Lexan Polycarbonate Body Shells, for RC Models:
RCScrapyard Radio Controlled Models
Flags

Touring Car Body Shells, for RC Models













Items For Sale:




Flags

Hints and Tips

Painting a Lexan Body Shell.

   Most RC Model kits come with an unpainted, clear Lexan plastic Body Shell you yourself must prepare and paint. This type of Body Shell is painted on the inside, and special spray or brush on Polycarbonate Paints MUST be used.

   The beauty of this is you can go wild and show off your artistic ability, or simply choose your favourite colour, and add some choice decals later.

   This article is for those who have never done this kind of thing before, and need some basic guidance.


   Firstly, cut off the waste from the body shell with sharp scissors. If required finish off the rounded wheel arches with smooth sandpaper wrapped around a drinks can.

   Any holes for body posts must also be drilled before painting. Place the clear body shell over the model and adjust the posts so the shell is in the desired position. Where the posts touch the shell make a small dot with a marker pen.
Next, pierce small holes in the shell where the dots are from the inside. Place the shell on an old piece of wood and drill the post holes, again, from the inside.

   The next thing to do is clean it inside and out. Any small amount of impurity such as oil or grease could impair the adhesion of the paint.
For this, fill a bowl with water and use a small amount of washing up liquid with a soft sponge. Never use a scourer. Rinse well to ensure no residue remains.

   Most Body Shells come with a set of sticky back paper masks for the windows etc that are positioned on the inside. If not supplied, you will have to either make your own, or use masking tape. Run your thumb nail around the edges of each mask to ensure contact paint can creep into any open area and easily ruin your hard work, so please be vigilant.

   Tip: To protect against paint spilling out onto the outside of the body shell, use masking tape around the outside edges and wheel arches.

   Now you are ready to begin applying your paint. Find a well ventilated area and if spraying, use a breathing mask.
Three or four sprayed, or at least two brushed layers are recommended allowing around thirty minutes between layers.

   Once the paint is fully dry, to protect the paint from scratching, spray or brush over it with one or two layers of clear plastic varnish.

   When the varnish is completely dry, carefully remove the window masks. If necessary, use a modelling knife to lift an edge to grasp between your thumb and finger DO NOT RUSH.

   Decals can now be placed on your body shell. So they adhere better I recommend any square edges are rounded. This reduced the tendency for them to peel off.

For More Setup Information check out my Hints and Tips page.









^ TOP ^












Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.


   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Model Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.






Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors








On/Off Road
RC Models:

Radio
Equipment:

Accessories: