Tethered and Radio Controlled Model Engines
Share RCScrapyard on Facebook
RCScrapyard Radio Controlled Models
Flags
RCScrapyard.net contains Google AdSense Ads and Amazon Affiliate links, from which we may earn commission. See our Disclosure page for more information.
bar

Cyclon Glow / Nitro Engines

For Radio Controlled and Control-Line Models
Introduction

   The image below is a Cyclon 15 Kaz FAI F1C, 2.5cc Glow / Nitro Engine, made circa 2006 by Alexander Kalmykov, Novosibirsk, Siberia, Russia.

Cyclon Glow - Nitro Engine





CHECK AVAILABILITY
On Amazon





   The invention of the Glow Plug, by Ray Arden in 1948, created nothing less than a revolution in model engineering. From that point on, Control Line and RC was transformed, and with the new "Glow Plugs" having the same thread as the old Spark Plugs, old Ignition Engines could be instantly converted into Glow Engines.

   Fuelled by a mixture of nitromethane and methanol, the modern Nitro Engine Glow Plug has a platinum-iridium coil, that is initially heated using an electric current from a "Starter" to ignite the fuel and start the process. From this point, the heat produced from compression and combustion keeps the engine running until the flow of fuel is cut off or simply runs out.


















Flags





Hints, Tips and Information


Choosing the Correct Engine for your form of RC.

   When it comes to choosing an Engine for a used RC model you found on eBay or at a local garage sale, you may need some guidance, not only on the engine, but the type of tail pipe and carburettor it may need.

   In this article I give some basic detail on what you need to look for, depending on the form of your model (Car, Truck, Airplane, Boat etc), explaining the different requirements each form has to have.

Read the Complete Article  ▶ ▶

Why you should Break-in your New Nitro Engine before your first run

   If you were to examine a new nitro engine cylinder and the surface of the piston through a microscope, you would see thousands of grooves, peaks and troughs left by the reaming and honing process during production.

   As the piston slides up and down inside the cylinder, the peaks of the piston collide with those of the cylinder and break off to produce smaller and smaller peaks and troughs and after a short time produce almost perfectly smooth surfaces.

   This process must be done carefully, because if the engine is revved too high, the danger is that those peaks and troughs, instead of getting smaller, could rip chunks out of the surfaces reducing the efficiency of the engine.

   In this article, I describe how "run in" should be carried out, and how to tell if the fuel mixture needs adjustment.

Read the Complete Article  ▶ ▶

The Importance of Maintaining your Fuel System

   In order to run efficiently, model engines require a constant flow of fuel. If the flow is restricted or the fuel is contaminated in any way, not only could your engine loose power, it could cause irreparable damage.

   This informative article not only explains how to maintain and clean your fuel system, but how to troubleshoot any problems, what to look for and crucially, how to fix them.

Read the Complete Article  ▶ ▶

Glow Plugs for Nitro Engines

   If you have a clapped out, old nitro engine, don't have a manual, can find very little detail about your engine and are struggling to decide what kind of new glow-plug your engine needs, this article has been written to give you some insight into what you should be looking for.

Read the Complete Article  ▶ ▶

How to avoid Radio Interference

   Radio Interference is common across all forms of RC. In this article I have listed a number of hints and tips, gained over my many years of experience in RC, explaining how by making a few simple changes to the positioning of your receiver, or using some electronic components, you can easily avoid and protect your model from Interference..

Read the Complete Article  ▶ ▶


More Hints and Tips

   For more Radio Controlled Model Hints, Tips and Information, check out the list on the RCScrapyard Homepage. ▶ ▶








Exhaust - Tail Pipes Glow Plugs Carburetors Fuel Tanks Starters Glow-Starter Batteries Engine Kill Switch
Engine Bearings and Bearing Sets Spur Gears Nitro Fuel Pinion Gears Radio Transmitters etc







RC Models:
Radio
& Motors:
Other
Accessories: