1/10 Scale Electric Truck/Rock Crawler:

Team Associated Enduro Trail Truck, Sendero RTR - 40100 / 40100C - Radio Controlled Model

History and Info:

   Released by Team Associated in 2019, the Enduro Trail Truck, Sendero RTR - # 40100 - came with a Reedy Power 16T, 5-slot brushed crawler Motor, a SC400X ESC, 3-channel XP130 2.4GHz Radio system and 1320MG metal-gear servo.

   A Combo version was also available - # 40100C - with all of the above, plus a Reedy 3000mAh 30C 7.4V Shorty Battery and Reedy Compact Balance Charger.

   The Enduro chassis is built around the Stealth X gearbox, providing three levels of front and rear independent adjustment options: 27T and 53T gears (overdrives the front end 5.7%), 28T and 52T gears (provides a one-to-one drive ratio front to rear), and 26T and 54T gears (overdrives the front end 11.83%).

Team Associated Enduro Trail Truck, Sendero RTR

▼ Scroll Down for More Images ▼

The 4WD Enduro is shaft driven, on a steel ladder frame chassis, with coil spring over oil filled dampers, 3-piece telescopic drive-shafts with an extruded aluminum center section, universal joint front drive axles, Stealth X gearbox and a full set of ball bearings.

Model Versions:

#40100 Enduro Trail Truck, Sendero RTR
#40100C Enduro Trail Truck, Sendero RTR LiPo Combo

Features:

CMS (Chassis Mounted Servo)
Adjustable front track bar
Universal front drive axles
Stamped steel frame rails
Enclosed receiver box
12mm wheel hexes
Adjustable front and rear bumper mounts
Adjustable width rock sliders
Two battery boxes
Aluminum motor plate
Adjustable body posts
Optimized ball cups for more fluid axle articulation
Adjustable rear shock mount positions
Telescopic driveshafts front and rear
Extruded aluminum driveshaft splines
One-piece rear axle design
Splined front axle with adjustable caster
Machined input pinion gear
Metal ring gear
Machined steel top shaft
Metal idler gears
Heavy duty 5mm diameter steel links
Metal ball bearings included

(Source: Media Press Release)

Enduro Trail Truck, Sendero - 40100
Manual

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ Team Associated Enduro Trail Truck, Sendero RTR Chassis ★

★ Team Associated Enduro Ladder Frame Chassis ★

★ Team Associated Enduro Trail Truck, Sendero RTR Chassis ★

Buying a Used Associated Rock Crawler (and What to look for)

There are essentially three reasons you might want to buy a used Associated Rock Crawler; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Associated website, or purchased separately on eBay. With an instruction manual, any problems with your model Rock Crawler you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Associated model, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Associated models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Rock Crawler is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

Examine the Drive System

The gearbox of your used Rock Crawler should be opened up to check for damaged gears and wear. If there is excessive backlash in the gearing, these should be replaced. A thin coat of grease on the gears is enough to allow smooth operation and reduce further wear.

Pinions and Spur Gears

Gears are a weakness on all RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the motor mount and remember to check them for security after every two or three runs.

Steering Servo and Servo-Saver

Servo Gears
The steering servo is also prone to damage, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Don't Forget those Bearings

If your used Associated Rock Crawler comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Dampers

   Dampers, Shock Absorbers, Shocks - call them what you will, they are one of the least understood, but most important tools you have for adjusting the handling characteristics of your RC model.

   In this article, I will endeavour to explain just what you can achieve by making simple tweaks to your shocks, and how these tweaks can keep you ahead of your opposition on the track.

   In dictionary terms "Damper" is described as - "A mechanical device to absorb the energy of sudden impulses." - In plain language, they stop your car from bouncing all over the track.

So how do Dampers work?

Basically what you have is a small amount of silicone oil contained in a sealed cylinder. Through the centre of that cylinder is a metal rod, and on the end of that rod, a piston with a number of small holes in it. Pulling, or pushing the rod in and out of the cylinder, your will notice a certain amount of resistance as the oil is forced through the holes in the piston.

Read the Complete Article ▶ ▶

Hints, Tips and Information

Rubber Tires for RC Models

Rubber Tires ALWAYS should have either soft sponge or rubber inserts. They will not function as they should without them. And if you are totally serious about your racing they should be glued to the rims.

You should also have at least three different compounds (Soft, Medium and Hard) for varying track temperatures in On Road tarmac racing Touring cars and varying pin sizes for carpet and Off Road racing Buggys and Trucks.

How to Mount Rubber Tires onto Wheels/Rims.

Before mounting your Tires, I would recommend talking to the more experienced racers at your local club, concerning what inserts they use. Even the top level racers rely on a bit of local knowledge on tracks they have never raced before.

Read the Complete Article ▶ ▶

RC Models:

Radio
& Motors:

Other
Accessories:

Buggys
Formula 1
Monster Trucks
Rock Crawlers
Touring Cars
Trucks

Transmitters
Receivers
Crystals
Servos
Electric Motors
Nitro Engines

Batteries
ESC
Tires
Wheels
Bearings
Body Shells