1/10 Scale Electric Rally/Touring Car:

Team Magic E4-RS4 - TM 507018 - Radio Controlled Model

Navigation:

History and Info:

Introduced by Team Magic circa 2017, the 4WD E4RS4 Rubber Spec Touring Car Chassis - TM 507018 - was classed as a top spec competition bare chassis.

The model is belt driven, on a double deck woven graphite chassis, with front spool, rear gear type differential, coil spring over oil filled dampers, front double joint, with rear CVD drive-shafts, and a full set of ball bearings.

Team Magic E4RS4

▼ Scroll Down for More Images ▼

To race the Team Magic E4-RS4, it must be fine tuned to improve handling, provide responsive steering and give you the grip to cruise around corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our step by step procedure, will guide you to the best Set-up for your individual driving style.

Team Magic E4-RS4 - TM507018
Manual

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ Team Magic E4-RS4 Chassis ★

Buying a Used Team Magic E4-RS4
Touring Car (and What to look for)

There are essentially three reasons you might want to buy a used Team Magic E4-RS4 Electric Touring Car; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Magic website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Team Magic Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Team Magic models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Team Magic E4-RS4 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your E4-RS4 model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your E4-RS4 Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The E4-RS4 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Team Magic E4-RS4 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Team Magic Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your E4-RS4 model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Gearing to Win

   Just because you have the latest model, the best available batteries, the most powerful electric motor or nitro engine, doesn't mean you will go out and win everything in sight. The fastest car on the track is rarely the one that wins, it's the one that can accelerate out of corners under control, and remains consistent and efficient from the start to the end of a race.

   In days gone bye, all you had to consider was the number of mili amp hours (Mah) in your battery, and the current draw of your high powered motor. Gearing for a five minute race was a balancing act. But with the development of the new high capacity batteries, brushless motors and smart ESC, all that changed. Now, gearing is more of a matter of what suits your driving style and how quick your reflexes are on the sticks, the trigger and steer wheel of your transmitter. So, where do you start?

   At your local club track, you quickly find the right combination and set-up for your car by talking to the more experienced members. After a while, as your knowledge grows, tweaking a few things here and there can give you that small edge to keep you competitive. So, it follows that on tracks you don't know, you should talk to the locals there, who may be racing a similar model to your own, and adjust your set-up to suit.

   Gearing correctly for any given track is absolutely crucial if your car is to be competitive.

   Too high a gearing may get you in front at the start of a race, but as your motor begins to overheat and lose efficiency, that initial advantage will soon be lost.

Read the Complete Article ▶ ▶

Hints, Tips and Information

Make your RC Model Ball Bearings Work for You

   If you are serious about your racing, looking after your bearings is essential if you are to remain competitive.
   My own experience is in both Off and On Road, National and International Car racing, but most of these tips could be useful to all forms of RC.

   Shields: The main problem with Ball Bearing Shields is they create friction, and obviously the more you can reduce friction, the more efficient your bearings will be, so here's a tip that does just that.
   Wheel Bearings always come in pairs, positioned side by side. If you think about it, the two inside shields on each bearing are not required, so ... you can remove them using a small jewelers screwdriver ... simple. And in one fell swoop you have halved your wheel bearing friction.

Read the Complete Article ▶ ▶