Radio Controlled Models
Share RCScrapyard on Facebook
RCScrapyard Radio Controlled Models
Flags
RCScrapyard.net contains Google AdSense Ads and Amazon Affiliate links, from which we may earn commission. See our Disclosure page for more information.
bar

Tamiya TB Evolution IV MS Chassis Kit - 49353 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car Chassis:

  Released by Tamiya on March 23, 2005, the TB Evolution IV MS Chassis (#49353) is a Limited Edition, based on the prototype chassis that finished second in the 2005 YamaYama Cup in Japan.

Tamiya TB Evolution IV MS Chassis Kit - 49353

▼ Scroll Down for More Images ▼



  The fine-tuned TB Evolution IV MS has a number of improvements, including: A one-piece alloy lower bulkhead, New alloy center post with extra plastic parts, Alloy motor mount with heat sink, 2x22mm and 2x25mm stainless steel suspension shafts, Center cup reinforced with alloy part and one-piece cup joint.

  The model is shaft driven, on a carbon double deck chassis, with front one-way and rear ball differential, coil spring over oil filled dampers, anti roll bars, universal joint drive-shafts and a full set of ball bearings.

  A bodyshell, radio equipment, battery and charger must be purchased separately.

  To get the best from the Tamiya TB Evolution IV MS Chassis, it needs to be fine tuned to hug the corners at high speed, without slipping off the track and accelerate smoothly under control. Small adjustments can make a Big difference and our simple to understand, step by step procedure, will guide you to the best Set-up for your driving style.


Rating: 4.54.5 Stars out of 5 RCScrapyard



Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors




















Flags


Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis
Tamiya TB Evolution IV MS Chassis

Buying a Used Tamiya TB Evolution IV MS
Touring Car (and What to look for)


   There are essentially three reasons you might want to buy a used Tamiya TB Evolution IV MS Electric Touring Car; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

   Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

   If the body shell of your Tamiya TB Evolution IV MS is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your TB Evolution IV MS model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your TB Evolution IV MS Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
   The TB Evolution IV MS steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

   If body roll on your Tamiya TB Evolution IV MS is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your TB Evolution IV MS model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide



















Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks


















Hints, Tips and Information

How to put on Decals

   After spending lots of time and effort to paint your bodyshell, you come to the point where you make it look good by putting on all those flashy decals, but before you rush in with the scissors and start cutting, there are a few things you should do first.

   Good preparation is key to a perfect job, so before you do anything with your decals, you must first of all wash your hands, and then make sure the bodyshell is clean and no oil or grime from your previously grubby fingers remains on the Polycarbonate Lexan surface. Methylated spirits is the thing to use, or failing that, use one of those wipes you use for your computer monitor screen.

   As the body shell dries, you can carefully cut out the decals from the sheet. Do the big ones first and leave the smallest ones for last.

Read the Complete Article  ▶ ▶






Hints, Tips and Information

On Road Tires for Tarmac

   Modern day RC Model Rubber Tires for tarmac racing, generally come in wide or narrow format and in three compounds - Soft, Medium and Hard, each compound corresponding to different track temperatures.

   Inserts also come as soft, medium and hard, and are necessary to provide subtle but potentially race winning differences in grip, dependant on the grain structure of the tarmac used in the construction of the track.

   Club racers probably need just the three compound sets of tires, wide or narrow and with one particular type of insert. But if you are to venture into the world of National and International racing, you will need up to eighteen complete sets, to cover all the possible combinations of track condition, plus at least one set of wet weather tires.

Read the Complete Article  ▶ ▶







^ TOP ^

RC Models:
Radio
& Motors:
Other
Accessories: