Radio Controlled Models
Share RCScrapyard on Facebook
RCScrapyard Radio Controlled Models
Flags
RCScrapyard.net contains Google AdSense Ads and Amazon Affiliate links, from which we may earn commission. See our Disclosure page for more information.
bar

Tamiya M05 Pro Chassis - 58443 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car Chassis:

  Released by Tamiya on June 24, 2009, the M05 Pro is the upgraded version of the chassis and came without a bodyshell.

Tamiya M05-Pro

▼ Scroll Down for More Images ▼



  The 2WD, FWD (front wheel drive) M05 Pro Chassis has a lower centre of gravity than previous versions and good weight distribution which coupled with four wheel independent double wishbone suspension with coil spring over oil filed shock absorbers, orbital bevel gear differential and bell crank steering mechanism gives excellent stability and handling on high speed corners.

  The M05 pro Chassis has three possible wheelbase options: The basic 210mm, 225mm and 239mm, that are set by changing the position of the rear suspension parts.

  A full set of shielded ball bearings, aluminium rear uprights from the M-03R and blue anodised aluminium ball connectors and wheel nuts complete the Pro package.

  To drive, the M05 Chassis has much improved balance and the low centre of gravity provides excellent stability in comparison to the first FWD short wheelbase Tamiya models, the M01 and M03. However, it still needs some skill to keep it on its wheels and just like its predecessors, provides lots of fun.


Rating: 44 Stars out of 5 RCScrapyard



Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors





















Flags

Tamiya M05 Pro Chassis #58443
Tamiya M05 Pro Chassis #58443 Front
Tamiya M05 Pro Chassis #58443
Tamiya M05 Pro Chassis #58443 Rear

Buying a Used Tamiya M-05 Pro
Touring Car (and What to look for)


   There are essentially three reasons you might want to buy a used Tamiya M-05 Pro Electric Touring Car; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

   Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

   If the body shell of your Tamiya M-05 Pro is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your M-05 Pro model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your M-05 Pro Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
   The M-05 Pro steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

   If body roll on your Tamiya M-05 Pro is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your M-05 Pro model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide



















Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks


















Hints, Tips and Information

Tires for RC Models

Sponge (Foam) Tires

   Sponge Tires can be purchased either pre mounted, glued and trued on the rims, or separately. Fitting the Tires onto the rims can be messy, so here are a few tips to make it a bit easier.
   If you are fitting new Tires on old rims, make sure the old sponge Tire is completely removed. To do this, I recommend using a wood lathe and apiece of wood, at least 300mm long, and more than the width of your wheels, with medium grit emery paper stuck to it ... sand paper will also work, but emery is harder wearing ... This will also be used for truing a wheel. (Described later)

Read the Complete Article  ▶ ▶






Hints, Tips and Information

Battery Connectors

   Over the years I have been racing radio controlled model cars of all descriptions, I have tried a number of different connectors for my batteries.

   My first car was a Tamiya Boomerang, and of course the batteries I used all had the standard Tamiya connectors, which were fine with the kit supplied 27T silver can electric motor, but I soon discovered their problem when I installed my first Modified motor. The high current demands of the motor created so much heat, the plastic surround of the connectors melted and fused together. No matter how I tried they could not be disconnected. My only option was to cut the wires.

   From there I moved over to Corally connectors, commonly referred to by many now as Bullet connectors. Comprising of a short length of 4mm gold plated tube at one end, and what looks like what we used to call a Chinese lantern fitting that slotted inside the tube, also gold plated. Although they were highly efficient and reasonably easy to install and use, I never really took to this type of connector, I think it was the fact that there was always the possibility of the positive and negative being connected wrongly in poor light, and also that if positioned side by side, each connector could work loose and become exposed, leaving the possibility of a short circuit.

Read the Complete Article  ▶ ▶







^ TOP ^

RC Models:
Radio
& Motors:
Other
Accessories: